IDES Prospector Already have an account? Login Here

IDES

RAMTAL PM3007G2

Acetal (POM) Copolymer

Glass Fiber Reinforcement, 10%

Supplied by Polyram Ram-On Industries

The technical datasheet with complete property values for RAMTAL PM3007G2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
10% GLASS FIBER REINFORCED POLYACETAL FOR INJECTION MOULDING APPLICATIONS.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 10% Filler by Weight
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238, ISO 1133
Molding Shrinkage
      
Flow
in/in
 ASTM D955
--
%
 ISO 2577
Water Absorption
      
Saturation
%
 ASTM D570
Saturation, 73°F
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
      
73°F
ft·lb/in
 ASTM D256
73°F
ft·lb/in²
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Melting Temperature
°F
 ISO 11357-3, ASTM D3417
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Electric Strength
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.118 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RAMTAL PM3007G2, RAMTAL , RAMTALPM3007G2, PM 3007 G 2, PM3007G2, PM3007, 3007G, G2, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Polyram, AcetalPOMCopolymer, 3007PM
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Fill Speed: 25 to 50 mm/sec
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.