Already have an account?
Login Here
IDES
RAMTOUGH PZ300G6
Polycarbonate
Glass Fiber Reinforcement, 30%
Supplied by Polyram Ram-On Industries
The technical datasheet with complete property values for RAMTOUGH PZ300G6 is available to members of the
Prospector Plastics Database
.
Register to view full datasheet
.
Register to View Full Datasheet
Product Description
30% GLASS-FIBER REINFORCED POLYCARBONATE FOR INJECTION MOULDING APPLICATIONS.
General
Material Status
Commercial: Active
Availability
Africa & Middle East
Asia Pacific
Europe
Latin America
North America
South America
Filler / Reinforcement
Glass Fiber Reinforcement, 30% Filler by Weight
RoHS Compliance
Processing Method
Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
--
ASTM D792
--
g/cm³
ISO 1183
Melt Mass-Flow Rate (MFR)
(300°C/1.2 kg)
g/10 min
ASTM D1238
,
ISO 1133
Molding Shrinkage
Flow
in/in
ASTM D955
--
%
ISO 2577
Water Absorption
Saturation
%
ASTM D570
Saturation, 73°F
%
ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
(Yield)
psi
ASTM D638
,
ISO 527-2
Tensile Elongation
(Break)
%
ASTM D638
,
ISO 527-2
Flexural Modulus
psi
ASTM D790
,
ISO 178
Flexural Strength
psi
ASTM D790
,
ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
73°F
ft·lb/in
ASTM D256
73°F
ft·lb/in²
ISO 180
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
66 psi, Unannealed
°F
ASTM D648
,
ISO 75-2/B
264 psi, Unannealed
°F
ASTM D648
,
ISO 75-2/A
Thermal Conductivity
Btu·in/hr/ft²/°F
ASTM C177
,
DIN 52612
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
IEC 60093
Volume Resistivity
ohm·cm
IEC 60093
Dielectric Constant
(1 MHz)
IEC 60250
Electric Strength
V/mil
IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
(0.118 in)
UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RAMTOUGH PZ300G6, RAMTOUGH , RAMTOUGHPZ300G6, PZ 300 G 6, PZ300G6, PZ300, 300G, G6, Polycarbonate, PC, Polyram, 300PZ
Injection
Nominal Value
Unit
Drying Temperature
°F
Drying Time
hr
Suggested Max Moisture
%
Rear Temperature
°F
Middle Temperature
°F
Front Temperature
°F
Processing (Melt) Temp
°F
Mold Temperature
°F
Injection Pressure
psi
Holding Pressure
psi
Back Pressure
psi
Screw Speed
rpm
Injection Notes
Fill Speed: 25 to 50 mm/sec
Notes
1
Typical properties: these are not to be construed as specifications.
Copyright © 2012
IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.