INEOS LDPE M21G764 Ineos Polyolefins Polyethylene, Low Density

Product Description

M21G764 are particularly suitable for mono and co-extrusion applications such as deep freeze, form fill seal film in general and thin bags. In blends and co-extrusions, they can be used to boost the impact strength of LLDPE, LDPE and recycled polyethylene.

M21G764 are ionomers, produced by neutralisation of an ethylene - methacrylic acid copolymer. M21G764 contains only antiblock. They offer the following properties:

Very high impact strength at ambient and low temperatures

Exceptional drawdown

M 21 G 764 can be added if a lower slip level is required or used pure for low slip films. Addition of other polymers, masterbatches and pigments, or use of other thicknesses may alter film slip and antiblock performance.

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.
We recommend that you consult your INEOS technical representative for further advice on the use of M21G764.

General

Material Status

Commercial: Active

Availability

Europe

Additive

Antiblock (1130 ppm)¹

Antioxidant

Features

Antiblocking

Antioxidant

Copolymer

Good Drawdown

Low Temperature Impact Resistance

Ultra High Impact Resistance

Uses

Bags

Blending

Film

Foam

Seals

RoHS Compliance

Forms

Pellets

Processing Method

Blown Film

Coextrusion

Extrusion

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/0.325 kg)		g/10 min	ISO 1133
Methacrylic Acid Content		%	Internal Method
Mechanical	Nominal Value	Unit	Test Method
Coefficient of Friction (Blown Film)			ASTM D1894
Films	Nominal Value	Unit	Test Method
Film Thickness - Tested		mil
Tensile Modulus			ISO 1184
1% Secant, MD: 2.0 mil, Blown Film		psi
1% Secant, TD: 2.0 mil, Blown Film		psi
Tensile Stress			ISO 1184
MD: Yield, 2.0 mil, Blown Film		psi
TD: Yield, 2.0 mil, Blown Film		psi
MD: 2.0 mil, Blown Film		psi
TD: 2.0 mil, Blown Film		psi
Tensile Elongation			ISO 1184
MD: Break, 2.0 mil, Blown Film		%
TD: Break, 2.0 mil, Blown Film		%
Dart Drop Impact (2.0 mil, Blown Film)		g	ASTM D1709A
Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature		°F	ISO 306/A50
Optical	Nominal Value	Unit	Test Method
Gloss (45°, 1.97 mil, Blown Film)			ASTM D2457
Haze (1.97 mil, Blown Film)		%	ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LDPE M21G764, INEOS LDPE , INEOSLDPEM21G764, INEOSLDPE, LDPEM 21 G 764, LDPEM21G764, LDPEM21, LDPE, M 21 G 764, M21G764, M21, 21G, G764, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLowDensity, 21M, 21LDPEM
Features
Features may also be described by the following terms: Ultra High Impact Resistance, Antiblocking, Unspecified Antiblock, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Drawdown, Good draw down.

Extrusion	Nominal Value	Unit
Melt Temperature		°F

Notes

¹Silica

²Typical properties: these are not to be construed as specifications.

INEOS LDPE M21G764

Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe