IDES Prospector Already have an account? Login Here

IDES

INEOS LLDPE LL8109AA

Linear Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe

The technical datasheet with complete property values for INEOS LLDPE LL8109AA is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LLDPE for Blown film

LL8109AA has been developed for use in rich blends for mulch film, refuse sacks, liners and other thin film applications where excellent mechanical performance is required.

Characteristics
LL8109AA is a linear low density polyethylene copolymer containing hexene-1 as the comonomer. It offers the following properties:
  • Excellent impact strength and puncture resistance
  • High tear strength
  • Good optical properties
  • Good bubble stability
  • Excellent sealing characteristics

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.

We recommend that you consult your INEOS O&P Europe technical representative for further advice on the use of LL8109AA.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antioxidant
Features 
  • Antioxidant
  • Copolymer
  • Good Heat Seal
  • Good Impact Resistance
  • Good Tear Strength
  • Hexene Comonomer
  • Opticals
  • Puncture Resistant
Uses 
  • Bags
  • Blending
  • Film
  • Liners
  
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus
     ISO 1184
1% Secant, MD: 0.98 mil, Blown Film
psi
  
1% Secant, TD: 0.98 mil, Blown Film
psi
  
Tensile Stress
     ISO 527-3
MD: Yield, 0.98 mil, Blown Film
psi
  
TD: Yield, 0.98 mil, Blown Film
psi
  
MD: 0.98 mil, Blown Film
psi
  
TD: 0.98 mil, Blown Film
psi
  
Tensile Elongation
     ISO 1184
MD: Break, 0.98 mil, Blown Film
%
  
TD: Break, 0.98 mil, Blown Film
%
  
Dart Drop Impact (0.98 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength 2
     ASTM D1922
MD: 1.0 mil
lbf/in
  
TD: 1.0 mil
lbf/in
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A50
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 0.984 mil, Blown Film)
 
 ASTM D2457
Haze (0.984 mil, Blown Film)
%
 ASTM D1003
Additional Information
Film properties taken from 25 µm film, 2.5:1 blow up ratio, 200°C melt temperature.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LLDPE LL8109AA, INEOS LLDPE , INEOSLLDPELL8109AA, INEOSLLDPE, LLDPELL 8109 AA, LLDPELL8109AA, LLDPELL8109, LLDPE, LL 8109 AA, LL8109AA, LL8109, 8109AA, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLinearLowDensity, 8109LL, 8109LLDPELL
Features
Features may also be described by the following terms: Good Heat Seal, Hexene Comonomer, Good Puncture Resistance, Puncture Resistant, Good Tear Strength, Good Impact Resistance.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Blown Film
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.