INEOS LLDPE LL6608AF Ineos Polyolefins Polyethylene, Linear Low Density

Product Description

LL6608AF has been developed for lean and rich blend blown film applications, such as rigid layers in coextrusion, carrier bags, refuse sacks and liners. This grade is also recommended for artificial grass applications.
LL6608AF is a linear low density polyethylene copolymer containing hexene-1 as the comonomer. It offers the following properties:

Optimum balance between stiffness and film strength

Good optical properties

Good bubble stability

Excellent sealability and hot-tack strength

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.

We recommend that you consult your INEOS O&P Europe technical representative for further advice on the use of LL6608AF.

General

Material Status

Commercial: Active

Availability

Europe

Additive

Antioxidant

Features

Antioxidant

Copolymer

Good Heat Seal

Good Stiffness

Good Strength

Hexene Comonomer

Opticals

Uses

Bags

Film

Liners

RoHS Compliance

Forms

Pellets

Processing Method

Blown Film

Coextrusion

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)		g/10 min	ISO 1133
Films	Nominal Value	Unit	Test Method
Film Thickness - Tested		mil
Tensile Modulus - 1% Secant (1.5 mil, Blown Film)		psi	ISO 527-3
Tensile Stress			ISO 527-3
MD: Yield, 1.5 mil, Blown Film		psi
TD: Yield, 1.5 mil, Blown Film		psi
MD: 1.5 mil, Blown Film		psi
TD: 1.5 mil, Blown Film		psi
Tensile Elongation			ISO 527-3
MD: Break, 1.5 mil, Blown Film		%
TD: Break, 1.5 mil, Blown Film		%
Dart Drop Impact (1.5 mil, Blown Film)		g	ASTM D1709A
Elmendorf Tear Strength²			ASTM D1922
MD: 1.5 mil		lbf/in
TD: 1.5 mil		lbf/in
Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature		°F	ISO 306/A
Optical	Nominal Value	Unit	Test Method
Gloss (45°, 1.50 mil, Blown Film)			ASTM D2457
Haze (1.50 mil, Blown Film)		%	ASTM D1003
Additional Information
Film properties taken from 38 µm film, 2:1 blow up ratio, 230°C melt temperature.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LLDPE LL6608AF, INEOS LLDPE , INEOSLLDPELL6608AF, INEOSLLDPE, LLDPELL 6608 AF, LLDPELL6608AF, LLDPELL6608, LLDPE, LL 6608 AF, LL6608AF, LL6608, 6608AF, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLinearLowDensity, 6608LL, 6608LLDPELL
Features
Features may also be described by the following terms: Hexene Comonomer, Good Heat Seal, Good Stiffness, Good Strength.

Extrusion	Nominal Value	Unit
Melt Temperature		°F

Notes

¹Typical properties: these are not to be construed as specifications.

²Blown Film

INEOS LLDPE LL6608AF

Linear Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe