INEOS LLDPE LL6910AA Ineos Polyolefins Polyethylene, Linear Low Density

Product Description

LL6910AA is particularly suitable for use in lean and rich blend blown film applications, such as overwrap, counter bags, shrink film (lean blends, 10 to 30% LLDPE) and boil-in-the-bag applications. This grade is also recommended for artificial grass applications.

LL6910AA is a linear low density polyethylene copolymer containing hexene-1 as the comonomer. It offers the following properties:

Very high stiffness and downgauging potential

Good optical properties

High temperature resistance

High water vapour barrier properties

High creep resistance

Excellent sealability and hot-tack strength

For shrink film, higher shrink holding force and improved burn-through resistance

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.

We recommend that you consult your INEOS O&P Europe technical representative for further advice on the use of LL6910AA.

General

Material Status

Commercial: Active

Availability

Europe

Additive

Antioxidant

Features

Antioxidant

Copolymer

Good Creep Resistance

Hexene Comonomer

High Heat Resistance

High Stiffness

Opticals

Uses

Bags

Blending

Film

Shrink Wrap

RoHS Compliance

Forms

Pellets

Processing Method

Blown Film

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)		g/10 min	ISO 1133
Films	Nominal Value	Unit	Test Method
Film Thickness - Tested		mil
Tensile Modulus - 1% Secant (1.5 mil, Blown Film)		psi	ISO 1184
Tensile Stress			ISO 527-3
MD: Yield, 1.5 mil, Blown Film		psi
TD: Yield, 1.5 mil, Blown Film		psi
MD: 1.5 mil, Blown Film		psi
TD: 1.5 mil, Blown Film		psi
Tensile Elongation			ISO 1184
MD: Break, 1.5 mil, Blown Film		%
TD: Break, 1.5 mil, Blown Film		%
Dart Drop Impact (1.5 mil, Blown Film)		g	ASTM D1709A
Elmendorf Tear Strength²			ASTM D1922
MD: 1.5 mil		lbf/in
TD: 1.5 mil		lbf/in
Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature		°F	ISO 306/A50
Optical	Nominal Value	Unit	Test Method
Gloss (45°, 1.50 mil, Blown Film)			ASTM D2457
Haze (1.50 mil, Blown Film)		%	ASTM D1003
Additional Information
Film properties taken from 38 µm film, 2:1 blow up ratio, 230°C melt temperature.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LLDPE LL6910AA, INEOS LLDPE , INEOSLLDPELL6910AA, INEOSLLDPE, LLDPELL 6910 AA, LLDPELL6910AA, LLDPELL6910, LLDPE, LL 6910 AA, LL6910AA, LL6910, 6910AA, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLinearLowDensity, 6910LL, 6910LLDPELL
Features
Features may also be described by the following terms: High Stiffness, Hexene Comonomer, Good Creep Resistance, Creep Resistant, High Heat Resistance.
Uses
Uses may also be described by the following terms: Shrink Wrap.

Extrusion	Nominal Value	Unit
Melt Temperature		°F

Notes

¹Typical properties: these are not to be construed as specifications.

²Blown Film

INEOS LLDPE LL6910AA

Linear Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe