IDES Prospector Already have an account? Login Here

IDES

INEOS LLDPE LL2209AF

Linear Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe

The technical datasheet with complete property values for INEOS LLDPE LL2209AF is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LL2209 AF is suitable for a wide range of blown films either pure or blended with LDPE and other ethylene polymers. Use in sealing layers and in lamination is recommended.

LL2209 AF is a linear low density polyethylene copolymer containing butene-1 (C4) as the comonomer. It is specially formulated with processing aid to allow extrusion through a narrow die gap without melt fracture.
Film made from LL 2209 AF gives good bond strength after lamination and has the following advantages over conventional LDPE:
  • Superior hot-tack performance
  • Better sealing performance through contamination
  • Higher tensile strength and elongation at break
  • Higher puncture resistance

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.
We recommend that you consult your INEOS technical representative for further advice on the use of LL2209AF.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antioxidant
  • Processing Aid
  
Features 
  • Antioxidant
  • Bondability
  • Butene Comonomer
  • Good Heat Seal
  • Good Processability
  • High Elongation
  • High Strength
  • Puncture Resistant
Uses 
  • Blending
  • Film
  • Laminates
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction (Blown Film)
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus
     ISO 527-3
1% Secant, MD: 1.5 mil, Blown Film
psi
  
1% Secant, TD: 1.5 mil, Blown Film
psi
  
Tensile Stress
     ISO 527-3
MD: Yield, 1.5 mil, Blown Film
psi
  
TD: Yield, 1.5 mil, Blown Film
psi
  
MD: 1.5 mil, Blown Film
psi
  
TD: 1.5 mil, Blown Film
psi
  
Tensile Elongation
     ISO 527-3
MD: Break, 1.5 mil, Blown Film
%
  
TD: Break, 1.5 mil, Blown Film
%
  
Dart Drop Impact (1.5 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength 2
     ASTM D1922
MD: 1.5 mil
lbf/in
  
TD: 1.5 mil
lbf/in
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A50
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.50 mil, Blown Film)
 
 ASTM D2457
Haze (1.50 mil, Blown Film)
%
 ASTM D1003
Additional Information
Film properties taken from 38 µm film, 2.5:1 blow up ratio, 215°C melt temperature.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LLDPE LL2209AF, INEOS LLDPE , INEOSLLDPELL2209AF, INEOSLLDPE, LLDPELL 2209 AF, LLDPELL2209AF, LLDPELL2209, LLDPE, LL 2209 AF, LL2209AF, LL2209, 2209AF, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLinearLowDensity, 2209LL, 2209LLDPELL
Features
Features may also be described by the following terms: Butene Comonomer, High Elongation, High Strength, Good Puncture Resistance, Puncture Resistant, Bondability, Bondable, Good Heat Seal, Good Processability, Easy Processing.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Blown Film
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.