IDES Prospector Already have an account? Login Here

IDES

INEOS LDPE 28H430

Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe

The technical datasheet with complete property values for INEOS LDPE 28H430 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Applications
  • 28H430 is particularly suitable for nappy film and other hygienic films made by cast film coextrusion or blending. It can also be processed in blown film for thin rigid films with good optical properties
Characteristics
28H430 is an autoclave LDPE homopolymer. It offers the following properties:
  • High rigidity
  • Good downgauging potential
  • Low blocking
  • MFR tailored for cast extrusion
  • Good drawdown
If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Additive Free
  • Good Drawdown
  • High Rigidity
  • Homopolymer
  
Uses 
  • Blending
  • Cast Film
  • Film
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Blown Film
  • Cast Film
  • Coextrusion
  • Extrusion
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus
     ISO 1184
1% Secant, MD: 2.0 mil
psi
  
1% Secant, TD: 2.0 mil
psi
  
Tensile Stress
     ISO 1184
MD: Yield, 2.0 mil
psi
  
TD: Yield, 2.0 mil
psi
  
MD: Break, 2.0 mil
psi
  
TD: Break, 2.0 mil
psi
  
Tensile Elongation
     ISO 1184
MD: Break, 2.0 mil
%
  
TD: Break, 2.0 mil
%
  
Dart Drop Impact (2.0 mil)
g
 ASTM D1709A
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A50
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.97 mil)
 
 ASTM D2457
Haze (1.97 mil)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LDPE 28H430, INEOS LDPE , INEOSLDPE28H430, INEOSLDPE, LDPE 28 H 430, LDPE28H430, LDPE28, LDPE, 28 H 430, 28H430, 28H, H430, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLowDensity, H28, 28LDPE
Features
Features may also be described by the following terms: High Rigidity, Additive Free, No Additives, Good Drawdown, Good draw down.
Uses
Uses may also be described by the following terms: Cast Film.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Blown Film melt temperature range: 160 to 185°C
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.