IDES Prospector Already have an account? Login Here

IDES

Mediprene™ 502750M

Styrene Ethylene Butylene Styrene Block Copolymer

Supplied by ELASTO

The technical datasheet with complete property values for Mediprene™ 502750M is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Discontinued
Availability 
  • Europe
Features 
  • Clean/High Purity
  • Ethylene Oxide Sterilizable
  • Fast Molding Cycle
  • Food Contact Acceptable
  • Good Adhesion
  • Good Chemical Resistance
  • Good Colorability
  • Good Flexibility
  • Good Surface Finish
  • Good Weather Resistance
  • High Clarity
  • Low Compression Set
  • Low Extractables
  • Low Smoke Emission
  • Radiation Sterilizable
  • Recyclable Material
  • Soft
  • Steam Sterilizable
Uses 
  • Bags
  • Diaphrams
  • Film
  • Medical/Healthcare Applications
  • Membranes
  • Pharmaceutical Packaging
  • Pharmaceuticals
  • Seals
  • Tubing
Agency Ratings 
Appearance 
  • Translucent
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
     ASTM D638
100% Secant: Injection Molded
psi
  
300% Secant: Injection Molded
psi
  
Tensile Strength (Injection Molded)
psi
 ASTM D638
Tensile Elongation (Break, Injection Molded)
%
 ASTM D638
Elastomers
Nominal Value
Unit
Test Method
Tear Strength
lbf/in
 ASTM D624
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 0.157 in, Injection Molded)
 
 ASTM D2240
Additional Information
Service Temperature Range: -50 to 125°C
Related Terminology
This supplier and product may also be known by these terms: British Vita

Product names can be difficult to match. You may have searched any one of these terms to find this product: Mediprene™ 502750M, Mediprene 502750M, Mediprene™ , Mediprene, Mediprene502750M, 502750 M, 502750M, Styrene Ethylene Butylene Styrene Block Copolymer, SEBS, Thermoplastic Elastomer, TPE, Elasto, StyreneEthyleneButyleneStyreneBlockCopolymer, ThermoplasticElastomer, M502750
Features
Features may also be described by the following terms: Good Surface Finish, Low Extractables, High Purity, Clean, High Cleanliness, Good Flexibility, Flexible, High Clarity, Good Adhesion, Low Smoke Emission, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle, Low Compression Set, Radiation Sterilizable, Radiation Sterilization, gamma sterilization, gamma sterilizable, Steam Sterilization, Steam Sterilizable, Ethylene Oxide Sterilizable, EtO Sterilizable, EtO Sterilization, Ethylene Oxide Sterilizable, Good Colorability, Good Weather Resistance, Weather Resistant, Good Chemical Resistance, Chemical Resistant.
Uses
Uses may also be described by the following terms: Medical Applications, Pharmaceutical Packaging, Tubing, Tube.
Agency Ratings
This plastic material has 8 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ISO (1), FDA (1), BgVV (1), EN (1), EU (3), USP (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.