IDES Prospector Already have an account? Login Here

IDES

Alcryn® 2380 BK

Melt Processable Rubber

Supplied by Advanced Polymer Alloys

The technical datasheet with complete property values for Alcryn® 2380 BK is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Agency Ratings 
RoHS Compliance 
Appearance 
  • Black
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Elastomers
Nominal Value
Unit
Test Method
Tensile Set
%
 ASTM D412
Tensile Stress (100% Strain)
psi
 ASTM D412, ISO 37
Tensile Strength (Yield)
psi
 ASTM D412, ISO 37
Tensile Elongation (Break)
%
 ASTM D412, ISO 37
Tear Strength
      
75°F 2
lbf/in
 ASTM D624
75°F
lbf/in
 ISO 34-1
Compression Set
      
75°F, 22.0 hr
%
 ASTM D395A
212°F, 22.0 hr
%
 ASTM D395A
75°F, 22.0 hr 3
%
 ISO 815
212°F, 22.0 hr 3
%
 ISO 815
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
 ASTM D2240, ISO 868
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air
      
257°F, 168 hr
%
 ASTM D573, ISO 188
100% Strain, 257°F, 168 hr
%
 ASTM D573
100% Strain 257°F, 168 hr
%
 ISO 188
Change in Volume
      
212°F, 168 hr, in ASTM Oil #1
%
 ASTM D471
212°F, 168 hr, in IRM 903 Oil #3
%
 ASTM D471
212°F, 168 hr, in Water
%
 ASTM D471, ISO 1817
212°F, 168 hr, in ASTM #1 Oil
%
 ISO 1817
212°F, 57120 hr, in IRM 903 Oil #3
%
 ISO 1817
Fill Analysis
Nominal Value
Unit
Test Method
Apparent Viscosity (374°F, 300 sec^-1)
Pa·s
 ASTM D3835
Related Terminology
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of Ferro

Product names can be difficult to match. You may have searched any one of these terms to find this product: Alcryn® 2380 BK, Alcryn 2380 BK, Alcryn® , Alcryn, Alcryn2380BK, 2380 BK, 2380BK, Melt Processable Rubber, MPR, Thermoplastic Elastomer, TPE, APA, MeltProcessableRubber, ThermoplasticElastomer, BK2380
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
3Type A
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.