|
Density 2
|
|
g/cm³
|
ISO 1183 |
|
Molding Shrinkage 3
|
|
|
ISO 294-4 |
|
Across Flow: 374°F
|
|
%
|
|
|
Flow: 374°F
|
|
%
|
|
|
Water Absorption
|
|
|
ISO 62 |
|
73°F, 24 hr, 0.126 in
|
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
|
%
|
|
|
Spiral Flow 3 (374°F, 39.4 mil)
|
|
in
|
Internal Method |
|
Tensile Modulus (73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Stress
|
|
|
ISO 527-2 |
|
Break, 73°F
|
|
psi
|
|
|
Break, 257°F
|
|
psi
|
|
|
Break, 347°F
|
|
psi
|
|
|
Break, 437°F
|
|
psi
|
|
|
Break, 527°F
|
|
psi
|
|
|
Tensile Strain (Break, 73°F)
|
|
%
|
ISO 527-2 |
|
Flexural Modulus (73°F)
|
|
psi
|
ISO 178 |
|
Flexural Strength
|
|
|
ISO 178 |
|
437°F
|
|
psi
|
|
|
347°F
|
|
psi
|
|
|
257°F
|
|
psi
|
|
|
73°F
|
|
psi
|
|
|
Compressive Stress
|
|
|
ISO 604 |
|
73°F
|
|
psi
|
|
|
248°F
|
|
psi
|
|
|
392°F
|
|
psi
|
|
|
Charpy Notched Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 179/1eA |
|
Charpy Unnotched Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 179/1U |
|
Notched Izod Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 180/A |
|
Unnotched Izod Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 180 |
|
Shore Hardness (Shore D, 73°F)
|
|
|
ISO 868 |
|
Heat Deflection Temperature (264 psi, Unannealed)
|
|
°F
|
ISO 75-2/A |
|
Glass Transition Temperature
|
|
°F
|
ISO 11357-2 |
|
Melting Temperature
|
|
°F
|
ISO 11357-3 |
|
CLTE
|
|
|
ISO 11359-2 |
|
Flow: > 289°F
|
|
in/in/°F
|
|
|
Flow: < 289°F
|
|
in/in/°F
|
|
|
Transverse: < 289°F
|
|
in/in/°F
|
|
|
Transverse: > 289°F
|
|
in/in/°F
|
|
|
Specific Heat (73°F)
|
|
Btu/lb/°F
|
DSC |
|
Thermal Conductivity (73°F)
|
|
Btu·in/hr/ft²/°F
|
Internal Method |
|
Volume Resistivity 4 (73°F)
|
|
ohm·cm
|
ASTM D4496 |
|
Flame Rating - UL (0.0197 in)
|
|
|
UL 94 |
|
Glow Wire Flammability Index (0.0787 in)
|
|
°F
|
IEC 60695-2-12 |
|
Toxicity
|
|
|
NES 713 |
|
CO Content
|
|
|
|
|
CO2 Content
|
|
|
|
|
Total Gases
|
|
|
|
|
Melt Viscosity (752°F)
|
|
Pa·s
|
ISO 11443 |
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: VICTREX® PEEK 90CA30, VICTREX PEEK 90CA30, VICTREX® PEEK , VICTREX PEEK, VICTREXPEEK90CA30, VICTREXPEEK, PEEK 90 CA 30, PEEK90CA30, PEEK90, PEEK, 90 CA 30, 90CA30, 90CA, CA30, Polyetheretherketone, Polyaryletherketone, PAEK, Victrex, CA90, 90PEEK
|
|
Features may also be described by the following terms: Semi-Crystalline, Good Flow, Good Chemical Resistance, Chemical Resistant, Low Friction, High Strength, Good Wear Resistance, Wear Resistant.
|
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
|