IDES Prospector Already have an account? Login Here

IDES

Techno MUH M3100

Acrylonitrile Butadiene Styrene

Supplied by Techno Polymer America, Inc.

The technical datasheet with complete property values for Techno MUH M3100 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  
Features 
  • Good Chemical Resistance
  • High Heat Resistance
  • Shock Absorbent
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (73°F)
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield, 73°F)
psi
 ASTM D638
Tensile Elongation (Yield, 73°F)
%
 ASTM D638
Flexural Modulus (73°F)
psi
 ASTM D790
Flexural Strength (73°F)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-22°F, 0.126 in
ft·lb/in
  
-22°F, 0.252 in
ft·lb/in
  
73°F, 0.126 in
ft·lb/in
  
73°F, 0.252 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Flammability
Nominal Value
Unit
Test Method
UL File Number
 
  
Additional Information
CLTE, Flow ,ASTM D696: 7 to 9 cm^-5/cm/°C
Spiral Flow Length, 250°C/98MPa: 310 mm
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Techno MUH M3100, Techno MUH , TechnoMUHM3100, TechnoMUH, MUHM 3100, MUHM3100, MUH, M 3100, M3100, Acrylonitrile Butadiene Styrene, ABS, Techno Polymer, AcrylonitrileButadieneStyrene, 3100M, 3100MUHM
Features
Features may also be described by the following terms: High Heat Resistance, Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Screw Speed
rpm
  
Injection Notes
Injection Pressure: High
Retention Pressure: Low to Medium
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.