IDES Prospector Already have an account? Login Here

IDES

Hostaform® C 9021 10/1570

Acetal (POM) Copolymer

Supplied by Ticona

The technical datasheet with complete property values for Hostaform® C 9021 10/1570 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Chemical abbreviation according to ISO 1043-1: POM
Molding compound ISO 9988- POM-K, M-GCL, 03-002

POM copolymer

Standard Injection molding type, UV-stabilized with carbon black
good chemical resistance to solvents, fuel and strong alkalis as
well as good hydrolysis resistance high resistance to thermal and
oxidative degradation.


UL-registration for a thickness more than 1.5 mm as UL 94 HB,
temperature index UL 746 B electrical 110 °C, mechanical 90 °C.

Burning rate ISO 3795 and FMVSS 302 < 100 mm/min for a thickness more
than 1 mm.

Ranges of applications: exterior applications.

UL = Underwriters Laboratories (USA)
FMVSS = Federal Motor Vehicle Safety Standard (USA)
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
Additive 
  • Carbon Black
  • UV Stabilizer
  
Features 
  • Copolymer
  • Fuel Resistant
  • High Heat Resistance
  • Hydrolysis Resistant
  • Solvent Resistant
Uses 
  • Outdoor Applications
RoHS Compliance 
Processing Method 
  • Injection Molding
Resin ID (ISO 1043)
  • POM
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption (Saturation, 73°F)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1A/1
Tensile Stress (Yield)
psi
 ISO 527-2/1A/50
Tensile Strain (Yield)
%
 ISO 527-2/1A/50
Nominal Tensile Strain at Break
%
 ISO 527-2/1A/50
Tensile Creep Modulus
     ISO 899-1
1 hr
psi
  
1000 hr
psi
  
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Melting Temperature 2
°F
 ISO 11357-3
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index
V
 IEC 60112
Electric Strength
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0591 in
 
  
0.118 in
 
  
Additional Information
Nominal Value
Unit
Test Method
ISO Type
 
 ISO 9988-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 9021 10/1570, Hostaform C 9021 101570, Hostaform® , Hostaform, HostaformC9021101570, C 9021 10, C902110, C 9021 10/1570, C 9021 101570, C 9021 10:1570, C 9021 10+1570, C 9021 10-1570, C 9021 10_1570, C 9021 10 1570, C9021, 902110, 101570, C9021101570, Acetal Copolymer, Acetal Copolymer, C902110_1570, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 9021C
Features
Features may also be described by the following terms: High Heat Resistance.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Screw L/D Ratio
 
  
Injection Notes
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.
Notes
1Typical properties: these are not to be construed as specifications.
210°C/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.