IDES Prospector Already have an account? Login Here

IDES

VERSIFY™ 3300

Elastomer

Supplied by The Dow Chemical Company

The technical datasheet with complete property values for VERSIFY™ 3300 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
VERSIFY™ 3300 Elastomer can be used for stretch cling, elastic film and as a blend component in thermoplastic elastomers and thermoplastic olefins. It is a particularly good choice for cast stretch film sealants.

When used as cling additive the grade generates higher unstretched film cling levels and can be used in blends at lower addition levels than needed with VLDPE. It gives consistent performance in hot and cold conditions, retains its characteristics over extended periods and delivers lower noise levels.

Complies with:
  • U.S. FDA FCN 909
  • U.S. FDA 21 CFR 175.105(c)(5)
  • EU, No 10/2011
  • Consult the regulations for complete details.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Cast Film
  • Film Extrusion
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Total Crystallinity
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Break, Compression Molded)
psi
 ASTM D638
Tensile Elongation 2 (Break, Compression Molded)
%
 ASTM D638
Flexural Modulus - 1% Secant (Compression Molded)
psi
 ASTM D790
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness 3
     ASTM D2240
Shore A, Compression Molded
 
  
Shore D, Compression Molded
 
  
Thermal
Nominal Value
Unit
Test Method
Glass Transition Temperature (DSC)
°F
 Internal Method
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature (DSC)
°F
 Internal Method
Optical
Nominal Value
Unit
Test Method
Gardner Gloss
     ASTM D523
20°, 39.4 mil, Compression Molded
 
  
60°, 39.4 mil, Compression Molded
 
  
Haze (78.7 mil, Injection Molded)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: VERSIFY™ 3300, VERSIFY 3300, VERSIFY™ , VERSIFY, VERSIFY3300, 3300, TPO, Thermoplastic Polyolefin Elastomer, TPO (POE), TPO POE, Thermoplastic Elastomer, TPE, Dow, ThermoplasticPolyolefinElastomer, TPOPOE, ThermoplasticElastomer
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (2).
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
3Hardness after 10 seconds.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.