IDES Prospector Already have an account? Login Here

IDES

Kingfa FRABS-518

Acrylonitrile Butadiene Styrene

Supplied by Kingfa

The technical datasheet with complete property values for Kingfa FRABS-518 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  
Features 
  • Low Temperature Impact Resistance
Uses 
  • Power/Other Tools
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
     ASTM D1238
200°C/5.0 kg
g/10 min
  
220°C/10.0 kg
g/10 min
  
Molding Shrinkage - Flow (73°F)
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus 3
psi
 ASTM D790
Flexural Strength 3
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-22°F, 0.252 in
ft·lb/in
  
73°F, 0.126 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.252 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
Vicat Softening Temperature
      
--
°F
 ASTM D1525 4
--
°F
 ASTM D1525 5
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0630 in
 
  
0.118 in
 
  
0.0787 in
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Kingfa FRABS-518, Kingfa FRABS518, Kingfa , KingfaFRABS518, FRABS, FRABS-518, FRABS518, FRABS:518, FRABS/518, FRABS+518, FRABS_518, FRABS 518, Acrylonitrile Butadiene Styrene, ABS, AcrylonitrileButadieneStyrene, 518FRABS
Features
Features may also be described by the following terms: Low Temperatuer Impact Resistance, Low Temp Impact Resistance.
Uses
Uses may also be described by the following terms: Power Tools, Tools.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Injection Notes
Processing Temperature Limit: 230°C
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
30.079 in/min
4Rate A (50°C/h), Loading 2 (50 N)
5Rate B (120°C/h), Loading 1 (10 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.