IDES Prospector Already have an account? Login Here

IDES

Advanced Composites ATX832N

Compounded Polypropylene

Talc Filler

Supplied by Advanced Composites, Inc.

The technical datasheet with complete property values for Advanced Composites ATX832N is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Talc Filler
Features 
  • High Flow
  • High Impact Resistance
  • Scratch Resistant
Automotive Specifications 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR)
g/10 min
 ISO 1133
Molding Shrinkage (0.118 in)
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength
     ISO 180
-40°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Instrumented Dart Impact 2 (32°F)
in·lb
 ASTM D3763
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D, 15 sec)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Advanced Composites ATX832N, Advanced Composites , AdvancedCompositesATX832N, AdvancedComposites, CompositesATX 832 N, CompositesATX832N, CompositesATX832, Composites, ATX 832 N, ATX832N, ATX832, 832N, Polypropylene, Compounded, Polypropylene Compounded, TPO, Polypropylene, PP, Adv Composites, PolypropyleneCompounded, 832ATX, 832CompositesATX
Features
Features may also be described by the following terms: Scratch Resistant, Resists Scratches, High Impact Resistance, High Flow, High Melt, High MFI.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Cushion
in
  
Injection Notes
Injection Pressure: 10% over max fill pressure
Holding Pressure: 50 to 60% of max fill pressure
Injection Speed: 1 to 3 inches/sec
Screw RPM: 1 to 2 secs before mold open
Notes
1Typical properties: these are not to be construed as specifications.
222.0 ft/sec
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.