IDES Prospector Already have an account? Login Here

IDES

Andur 1-8 APLM/Curene® 442

Polyurethane (Polyester, TDI)

Supplied by Anderson Development Company

The technical datasheet with complete property values for Andur 1-8 APLM/Curene® 442 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Andur 1-8APLM is a polyester based liquid, toluene diisocyanate terminated prepolymer. An elastomer with a hardness of 79 to 82 Shore A is obtained when this prepolymer is cured with Curene® 442 [4,4'-methylene-bis (orthochloroaniline)]. Elastomers of lower hardness can be obtained by reaction with various poyols and their combination with Curene 442 and other diamines, or through the use of plasticizers.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Forms 
  • Liquid
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Molding Shrinkage - Flow
in/in
 ASTM D955
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress
     ASTM D412
100% Strain
psi
  
300% Strain
psi
  
Tensile Strength (Yield)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Compression Set
%
 ASTM D395B
Bayshore Resilience
%
 ASTM D2632
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
 ASTM D2240
Thermoset
Nominal Value
Unit
Test Method
Pot Life
min
  
Demold Time (212°F)
min
  
Post Cure Time (212°F)
hr
  
Additional Information
Durometer Hardness, ASTM D2240, Shore A: 79 to 82
Die C Tear, ASTM D1004: 345 pli
Average Split Tear, ASTM D1938: 215 pli
Stoichiometry Curative Level: 95%
Mix Temperature:
  • Andur 1-8 APLM: 180-212°F
  • Curene 442: 230-240°F
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Andur 1-8 APLM/Curene® 442, Andur 18 APLMCurene 442, Andur , Andur18APLMCurene442, 1 8 APLM Curene 442, 1-8 APLM/Curene® 442, 18 APLMCurene 442, 1-8 APLM:Curene® 442, 1-8 APLM+Curene® 442, 1-8 APLM-Curene® 442, 1-8 APLM_Curene® 442, 1-8 APLM Curene® 442, 1:8 APLM/Curene® 442, 1/8 APLM/Curene® 442, 1+8 APLM/Curene® 442, 1_8 APLM/Curene® 442, 1 8 APLM/Curene® 442, 18, 8APLM, APLMCurene, Curene442, 18APLMCurene442, 18 APLM_Curene 442, 18 APLM Curene 442, 1_8 APLMCurene 442, 1 8 APLMCurene 442, Polyurethane, 18APLM_Curene442, 1_8APLMCurene442, Polyurethane (Polyester, TDI), Polyurethane Polyester TDI, PUR-Ester/TDI, PUREsterTDI, PUR-Ester:TDI, PUR-Ester+TDI, PUR-Ester-TDI, PUR-Ester_TDI, PUR-Ester TDI, PUR:Ester/TDI, PUR/Ester/TDI, PUR+Ester/TDI, PUR_Ester/TDI, PUR Ester/TDI, PUR, Anderson, PolyurethanePolyesterTDI, PUREster_TDI, PUREster TDI, PUR_EsterTDI, PUR EsterTDI, 81
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.