IDES Prospector Already have an account? Login Here

IDES

Therma-Tech™ NJ-6000 TC

Polyamide 12

Supplied by PolyOne Corporation

The technical datasheet with complete property values for Therma-Tech™ NJ-6000 TC is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Therma-Tech™ Thermal Management Compounds have been engineered to combine the heat transfer and cooling capabilities of metals with the design freedom, weight reduction and cost advantages of thermoplastics. These materials provide the benefits of proprietary conductive additive technologies and the performance of select engineering thermoplastic resins. Therma-Tech compounds have been shown to improve thermal conductivity up to 100-times that of conventional plastics and can be used in a wide range of thermal management applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Electrically Conductive
  • Thermally Conductive
  
Uses 
  • Automotive Applications
  • Automotive Under the Hood
  • Consumer Applications
  • Electrical/Electronic Applications
  • Housings
  • Industrial Applications
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr, 0.125 in)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.250 in, Injection Molded)
ft·lb/in
 ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.250 in
°F
  
264 psi, Unannealed, 0.250 in
°F
  
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Therma-Tech™ NJ-6000 TC, ThermaTech NJ6000 TC, Therma-Tech™ , ThermaTech, Therma:Tech™, Therma/Tech™, Therma+Tech™, Therma_Tech™, Therma Tech™, ThermaTechNJ6000TC, Therma_Tech, Therma Tech, NJ, NJ-6000 TC, NJ6000 TC, NJ:6000 TC, NJ/6000 TC, NJ+6000 TC, NJ_6000 TC, NJ 6000 TC, NJ6000, 6000TC, NJ6000TC, NJ_6000TC, Polyamide 12, Nylon 12, Polyamide, Nylon, pa12, PolyOne, Polyamide12, Nylon12, 6000NJ
Generic Name
Generic Name may also be described by the following terms: PA12.
Features
Features may also be described by the following terms: Electrically Conductive, Conducts Electricity, Conductive.
Uses
Uses may also be described by the following terms: Housings, Housing, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Automotive Applications, Automotive Sector.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.