IDES Prospector Already have an account? Login Here

IDES

TAROMID A 280 G3 K3

Polyamide 66

Glass Bead\Glass Fiber, 30%

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROMID A 280 G3 K3 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Polyamide 66 medium viscosity 30% glass beads/glass fibres reinforced, very good surface finish and dimensional stability.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Glass Bead\Glass Fiber, 30% Filler by Weight
Features 
  • Good Dimensional Stability
  • Good Surface Finish
  • Medium Viscosity
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (280°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage
     Internal Method
Across Flow
%
  
Flow
%
  
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Granule Humidity 2
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Break)
psi
 ISO 527-2/50
Tensile Strain (Break)
%
 ISO 527-2/50
Flexural Modulus 3
psi
 ISO 178
Flexural Strength 3
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eU
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 4 (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
      
--
°F
 ISO 306/A50
--
°F
 ISO 306/B50
Ball Pressure Test (401°F)
 
 IEC 60695-10-2
Melting Temperature
°F
 ISO 11357-3
Continuous Use Temperature - 20000 hr 5
°F
 IEC 60216
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Dielectric Constant
 
 IEC 60250
Comparative Tracking Index
     IEC 60112
Solution A
V
  
Solution B
V
  
Electric Strength (0.0787 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Glow Wire Flammability Index (0.0787 in)
°F
 IEC 60695-2-12
Oxygen Index
%
 ASTM D2863
Additional Information
Nominal Value
Unit
Test Method
Reinforcement Content 6 (1382°F)
%
 ISO 3451
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID A 280 G3 K3, TAROMID A , TAROMIDA280G3K3, TAROMIDA, A 280 G 3 K 3, A280 G3 K3, A280, 280 G 3 K 3, A280G3K3, 280 G3 K3, 280G, G3, 3K, K3, 280G3K3, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Taro Plast, Polyamide66, Nylon66, G280, 280A
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Medium Viscosity, Good Surface Finish, Good Dimensional Stability, Dimensionally Stable.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Pre-heat Temperature: 80 to 100°C
Pre-heat Time: 3 hr
Notes
1Typical properties: these are not to be construed as specifications.
2TARO 002
30.039 in/min
4120°C/hr
5H120
61 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.