IDES Prospector Already have an account? Login Here

IDES

FRAGOM PR/100-G

Polyolefin

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for FRAGOM PR/100-G is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
FRAGOM is the trade-mark of our flame retardant halogen free polyolefine thermoplastic compounds.
FRAGOM PR/100G is a flexible flame retardant polyolefine thermo-plastic compound having high temperature index and good oxygen index, suitable for cable sheathing and insulation.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Flame Retardant
  • Halogen Free
  
Uses 
  • Cable Jacketing
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/21.6 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Elastomers
Nominal Value
Unit
Test Method
Compression Set (176°F, 4.00 hr)
%
 ASTM D395
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air (212°F, 168 hr)
%
 ISO 188
Change in Tensile Strain at Break in Air (212°F, 168 hr)
%
 ISO 188
Change in Tensile Stress (73°F, 4 hr, in Gasoline)
%
 ISO 1817
Change in Tensile Strain at Break (73°F, 4 hr, in Gasoline)
%
 ISO 1817
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Flammability
Nominal Value
Unit
Test Method
Oxygen Index
%
 ASTM D2863
Optical
Nominal Value
Unit
Test Method
Transmittance
%
 ASTM D1003
Additional Information
Conductivity: <0.60 µs cm-1
Temperature Index, 21% O2: 310°C
HCI Generation: 0%
Corrosivity: >4.5 PH
Tensile Strength Retention, Max Variation, CEI 167, in SAE 20 Oil, 4 hr, 70°C: <+/-20%
Elongation at Break Retention, Max Variation, CEI 167, in SAE 20 Oil, 4 hr, 70°C: <+/-20%
Tensile Strength Retention, Max Variation, CEI Test, in ASTM 2 Oil, 4 hr, 70°C: <+/-20%
Elongation at Break Retention, Max Variation, CEI Test, in ASTM 2 Oil, 4 hr, 70°C: <+/-20%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: FRAGOM PR/100-G, FRAGOM PR100G, FRAGOM , FRAGOMPR100G, PR, PR 100 G, PR/100-G, PR100G, PR:100-G, PR+100-G, PR-100-G, PR_100-G, PR 100-G, PR/100:G, PR/100/G, PR/100+G, PR/100_G, PR/100 G, PR100, 100G, PR_100G, PR 100G, PR100_G, PR100 G, Polyolefin, Unspecified, Polyolefin Unspecified, Polyolefin, Crosspolimeri, PolyolefinUnspecified, 100PR
Features
Features may also be described by the following terms: Zero Halogen Content, Halogen Free.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.