IDES Prospector Already have an account? Login Here

IDES

FRAGOM PR/6

Polyolefin

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for FRAGOM PR/6 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
FRAGOM is the trade-mark of our flame retardant halogen free polyolefine thermoplastic compounds.
FRAGOM PR/6 is a flame retardant polyolefine thermoplastic compound having high temperature index and good oxygen index, suitable for cable sheathing and insulation. Quality M1 CEI 2022 II.
Any good extruder designed for PE and PVC may be suitable for FRAGOM extrusion provided that it is equipped with a convenient head and a screw having agood homogenesing capacity. Extruders specially studied could be convenient.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Flame Retardant
  • Halogen Free
  
Uses 
  • Cable Jacketing
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/21.6 kg)
g/10 min
 ASTM D1238
Mooney Viscosity (250°F)
MU
 ASTM D1646
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Elastomers
Nominal Value
Unit
Test Method
Compression Set (176°F, 4.00 hr)
%
 ASTM D395
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
 ASTM D2240
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air (212°F, 168 hr)
%
 ISO 188
Change in Tensile Strain at Break in Air (212°F, 168 hr)
%
 ISO 188
Change in Tensile Stress     ISO 1817
73°F, 4 hr, in Gasoline
%
  
158°F, 4 hr, in ASTM #2 Oil
%
  
158°F, 4 hr, in SAE 20 Oil
%
  
Change in Tensile Strain at Break     ISO 1817
73°F, 4 hr, in Gasoline
%
  
158°F, 4 hr, in ASTM #2 Oil
%
  
158°F, 4 hr, in SAE 20 Oil
%
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Flammability
Nominal Value
Unit
Test Method
Oxygen Index
%
 ASTM D2863
Optical
Nominal Value
Unit
Test Method
Transmittance
%
 ASTM D1003
Additional Information
Insulation Resistance, 20°C: <=500 Mohm-km
Temperature Index, 21% O2: 380°C
HCI Generation: <=0.3%
Moisture Absorption, Gravimetric: 6 mg/cm²
Loss of Mass, IEC 540: -0.5%
Mooney Viscosity, 4 hr, 121°C: 50
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: FRAGOM PR/6, FRAGOM PR6, FRAGOM , FRAGOMPR6, PR, PR/6, PR6, PR:6, PR+6, PR-6, PR_6, PR 6, Polyolefin, Unspecified, Polyolefin Unspecified, Polyolefin, Crosspolimeri, PolyolefinUnspecified, 6PR
Features
Features may also be described by the following terms: Zero Halogen Content, Halogen Free.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.