IDES Prospector Already have an account? Login Here

IDES

GETILAN ATP/190 X1

Crosslinked Polyethylene

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for GETILAN ATP/190 X1 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
GETILAN is the trade-mark of our crosslinkable polythene.
GETILAN ATP/190 is a high density chemically crosslinkable polythene to produce insulation and sheathing of electricalcables.
It is a conveniently grafted polythene able to react in presence of moisture and of catalyst. We normally suggest our type MAC/202.

REACTION BETWEEN GRAFTING AND CATALYST:
These two polythenes, separately stored, must be mixed before starting extrusion in the ratio:
GRAFTING/CATALYST 95/5
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Crosslinkable
  • High Density
  
Uses 
  • Cable Jacketing
Agency Ratings 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 IEC 60811
Tensile Strain (Break)
%
 IEC 60811
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306
Hot Set 2
      
392°F
%
 IEC 60811
Residual
%
  
Service Temperature
°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: GETILAN ATP/190 X1, GETILAN ATP190 X1, GETILAN , GETILANATP190X1, ATP, ATP 190 X 1, ATP/190 X1, ATP190 X1, ATP:190 X1, ATP+190 X1, ATP-190 X1, ATP_190 X1, ATP 190 X1, ATP190, 190X, X1, ATP190X1, ATP_190X1, Polyethylene, Crosslinked, Polyethylene Crosslinked, XLPE, Polyethylene, PE, Crosspolimeri, PolyethyleneCrosslinked, 190ATP
Features
Features may also be described by the following terms: High Density, High Specific Gravity.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): DIN (1).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
CROSSLINKING:
Crosslinking of the finished product is obtained by:
  • Immersion of the bobbin into hot water at 85/90 °C for two hours (up to 3 mm thickness).
  • Steam treatment at 0.15 for bar 5/6 hours.
  • Faster ambient curing is possible depending from the atmospheric conditions.
Notes
1Typical properties: these are not to be construed as specifications.
220 N/cm²
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.