IDES Prospector Already have an account? Login Here

IDES

GETILAN ATP/190 X1 3A

Crosslinked Polyethylene

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for GETILAN ATP/190 X1 3A is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
GETILAN is the trade-mark of our crosslinkable polythene.
GETILAN ATP/190 X1 3A is a high density antiflame chemically crosslinkable polythene with high temperature index and low halogen content. Suitable for automotive cables insulation.
It is a conveniently grafted polythene able to react in presence of moisture and of catalyst. We normally suggest our catalyst type MAC/203 HS MAC/203 HSL (less reactive).

REACTION BETWEEN GRAFTING AND CATALYST:
These two polythene, separately stored, must be mixed before starting extrusion in the ratio:
GRAFTING/CATALYST 92,5/7,5

Certify: SAE J1127/J1128 ,LV 112,ISO 6722 T3-T3S
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Crosslinkable
  • Flame Retardant
  • Low Halogen Content
Uses 
  • Automotive Applications
  • Cable Jacketing
  
Agency Ratings 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Hot Set 2
     IEC 60811
392°F
%
  
Residual: 392°F
%
  
Service Temperature
°F
  
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air (302°F, 168 hr)
%
 IEC 60811
Change in Tensile Strain at Break in Air (302°F, 168 hr)
%
 IEC 60811
Heat Aging 3 (347°F)
 
  
Flammability
Nominal Value
Unit
Test Method
Oxygen Index
%
 ASTM D2863
Halogen Content
%
 IEC 60754-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: GETILAN ATP/190 X1 3A, GETILAN ATP190 X1 3A, GETILAN , GETILANATP190X13A, ATP, ATP 190 X 1 3 A, ATP/190 X1 3A, ATP190 X1 3A, ATP:190 X1 3A, ATP+190 X1 3A, ATP-190 X1 3A, ATP_190 X1 3A, ATP 190 X1 3A, ATP190, 190X, X1, 13, 3A, ATP190X13A, ATP_190X13A, Polyethylene, Crosslinked, Polyethylene Crosslinked, XLPE, Polyethylene, PE, Crosspolimeri, PolyethyleneCrosslinked, 190ATP
Features
Features may also be described by the following terms: Low Halogen Content.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ISO (1), LV (1), SAE (2).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
CROSSLINKING:
Crosslinking of the finished product is obtained by:
  • Immersion of the bobbin into hot water at 85/90°C for two hours (up to 3 mm thickness).
  • Steam treatment at 0.15 for bar 5/6 hours.
  • Faster ambient curing is possible depending from the atmospheric conditions.
Notes
1Typical properties: these are not to be construed as specifications.
220 N/cm²
36 hr on mandrel
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.