IDES Prospector Already have an account? Login Here

IDES

GETILAN GPE/400 G

Crosslinked Polyethylene

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for GETILAN GPE/400 G is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
GETILAN is the trade-mark of our crosslinkable polythene.
GETILAN GPE/400 G is a medium density chemically crosslinkable compound for power insulation, suitable also for G7.
It is a conveniently grafted polythene able to react in presence of moisture and of a catalyst.
Normally we suggest our catalyst type MAC/202 or MAC/203 (suitable for extrusioin temperature lower than 215/220°C)

REACTION BETWEEN GRAFTING AND CATALYST:
These two polythenes, separately stored, must be mixed before starting extrusion in the ratio:
GRAFTING/CATALYST 94/6
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Crosslinkable
Uses 
  • Cable Jacketing
Agency Ratings 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Water Absorption - 24 hr (212°F)
lb/ream
 IEC 60811
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 IEC 60811
Tensile Strain (Break)
%
 IEC 60811
Thermal
Nominal Value
Unit
Test Method
Hot Set 2     IEC 60811
--
%
  
Residual
%
  
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air     IEC 60811
261°F, 40 hr
%
  
302°F, 168 hr
%
  
Change in Tensile Strain at Break in Air     IEC 60811
261°F, 40 hr
%
  
302°F, 168 hr
%
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 BS 6622
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: GETILAN GPE/400 G, GETILAN GPE400 G, GETILAN , GETILANGPE400G, GPE, GPE/400 G, GPE400 G, GPE:400 G, GPE+400 G, GPE-400 G, GPE_400 G, GPE 400 G, GPE400, 400G, GPE400G, GPE_400G, Polyethylene, Crosslinked, Polyethylene Crosslinked, XLPE, Polyethylene, PE, Crosspolimeri, PolyethyleneCrosslinked, 400GPE
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): CEI (1), IEC (1).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
CROSSLINKING:
Crosslinking of the finished product is obtained by:
  • Immersion of the bobbin into hot water at 85/90°C for two hours (up to 3 mm thickness).
  • Steam treatment at 0.15 for bar 5/6 hours.
  • Faster ambient curing is possible depending from the atmospheric conditions.
Notes
1Typical properties: these are not to be construed as specifications.
220 N/cm²
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.