|
Specific Gravity
|
|
|
|
|
--
|
|
|
ASTM D792 |
|
--
|
|
g/cm³
|
ISO 1183 |
|
Molding Shrinkage
|
|
|
|
|
Flow: 0.0625 in
|
|
in/in
|
ASTM D955 |
|
Flow: 0.125 in
|
|
in/in
|
ASTM D955 |
|
Across Flow: 0.0625 in
|
|
in/in
|
ASTM D955 |
|
Across Flow: 0.125 in
|
|
in/in
|
ASTM D955 |
|
Across Flow: 0.0625 in
|
|
%
|
ISO 294-4 |
|
Flow: 0.0625 in
|
|
%
|
ISO 294-4 |
|
Across Flow: 0.125 in
|
|
%
|
ISO 294-4 |
|
Flow: 0.125 in
|
|
%
|
ISO 294-4 |
|
Taber Abrasion Resistance (1000 Cycles, 1.0E+6 g, CS-17 Wheel)
|
|
mg
|
ASTM D1044 |
|
Tensile Set (100% Strain)
|
|
%
|
ASTM D412 |
|
Tensile Stress
|
|
|
|
|
100% Strain
|
|
psi
|
ASTM D412 |
|
100% Strain, 73°F
|
|
psi
|
ISO 37 |
|
Tensile Strength (Yield, 73°F)
|
|
psi
|
ASTM D412, ISO 37 |
|
Tensile Elongation
|
|
|
|
|
Break
|
|
%
|
ASTM D412 |
|
Break, 73°F
|
|
%
|
ISO 37 |
|
Tear Strength 2 (75°F)
|
|
lbf/in
|
ASTM D624 |
|
Compression Set
|
|
|
ASTM D395B, ISO 815 |
|
75°F, 22.0 hr
|
|
%
|
|
|
158°F, 22.0 hr
|
|
%
|
|
|
212°F, 22.0 hr
|
|
%
|
|
|
Durometer Hardness (Shore A, 5 sec)
|
|
|
ASTM D2240, ISO 868 |
|
Brittleness Temperature
|
|
°F
|
ASTM D746, ISO 812 |
|
Change in Tensile Strength in Air
|
|
|
|
|
158°F, 168 hr
|
|
%
|
ASTM D573, ISO 188 |
|
100% Strain, 158°F, 168 hr
|
|
%
|
ASTM D573 |
|
212°F, 168 hr
|
|
%
|
ASTM D573, ISO 188 |
|
100% Strain, 212°F, 168 hr
|
|
%
|
ASTM D573 |
|
100% Strain 158°F, 168 hr
|
|
%
|
ISO 188 |
|
100% Strain 212°F, 168 hr
|
|
%
|
ISO 188 |
|
Change in Ultimate Elongation in Air
|
|
|
ASTM D573 |
|
158°F, 168 hr
|
|
%
|
|
|
212°F, 168 hr
|
|
%
|
|
|
Change in Tensile Strain at Break
|
|
|
ISO 1817 |
|
158°F, 168 hr
|
|
%
|
|
|
212°F, 168 hr
|
|
%
|
|
|
Change in Volume
|
|
|
|
|
75°F, 168 hr, in Reference Fuel B
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in ASTM Oil #1
|
|
%
|
ASTM D471 |
|
212°F, 168 hr, in IRM 903 Oil
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in Water
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in ASTM #1 Oil
|
|
%
|
ISO 1817 |
|
Melt Viscosity (374°F, 300 sec^-1)
|
|
Pa·s
|
ASTM D3835 |
|
The value listed as Density -Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.
The value listed as Density, ISO 1183, was tested in accordance with ISO 2781.
|
|
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of Ferro
Product names can be difficult to match. You may have searched any one of these terms to find this product: DuraGrip® DGR 6880NC, DuraGrip DGR 6880NC, DuraGrip® , DuraGrip, DuraGripDGR6880NC, DGR 6880 NC, DGR 6880NC, DGR6880, 6880NC, DGR6880NC, Thermoplastic Elastomer, TPE, APA, ThermoplasticElastomer, 6880DGR
|
|
Features may also be described by the following terms: Good Colorability, Good Adhesion.
|
|
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EU (1).
|