IDES Prospector Already have an account? Login Here

IDES

Abstron HCR-15 M

Acrylonitrile Butadiene Styrene

Supplied by Bhansali Engineering Polymers Limited

The technical datasheet with complete property values for Abstron HCR-15 M is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Good Chemical Resistance
  • High Heat Resistance
  
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield, 0.126 in)
psi
 ASTM D638
Flexural Modulus (0.252 in)
psi
 ASTM D790
Flexural Strength (Yield, 0.252 in)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
0.126 in
ft·lb/in
  
0.252 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Annealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525 3
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.126 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Abstron HCR-15 M, Abstron HCR15 M, Abstron , AbstronHCR15M, HCR, HCR-15 M, HCR15 M, HCR:15 M, HCR/15 M, HCR+15 M, HCR_15 M, HCR 15 M, HCR15, 15M, HCR15M, HCR_15M, Acrylonitrile Butadiene Styrene, ABS, Bhansali Eng Poly, AcrylonitrileButadieneStyrene, 15HCR
Features
Features may also be described by the following terms: High Heat Resistance, Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Drying Time (Tray Oven): 3 to 3.5 hr
Drying Time (Hopper Dryers): 2.5 to 3 hr
Drying Time (Dry Air Ovens): 2 to 2.5 hr
Injection Pressure: Medium to High
Back Pressure: Medium to High
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
3Rate B (120°C/h)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.