IDES Prospector Already have an account? Login Here

IDES

LONGLITE® PBT 3015-104

Polybutylene Terephthalate

Glass Fiber Reinforcement, 15%

Supplied by Chang Chun Plastics Co., LTD.

The technical datasheet with complete property values for LONGLITE® PBT 3015-104 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 15% Filler by Weight
Features 
  • Fuel Resistant
  • Good Chemical Resistance
  • Good Moldability
  • Good Wear Resistance
  • Good Weather Resistance
  • High Heat Resistance
  • Oil Resistant
  • Solvent Resistant
Uses 
  • Electrical/Electronic Applications
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage
     ASTM D955
Flow: 0.0630 in
in/in
  
Across Flow: 0.0630 in
in/in
  
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.250 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Melting Temperature
°F
 DSC
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149
Dielectric Constant (60 Hz)
 
 ASTM D150
Dissipation Factor (60 Hz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0315 in, ALL)
 
 UL 94
UL
Nominal Value
Unit
Test Method
RTI Str (0.0327 in)
°F
 UL 746
RTI Imp (0.0327 in)
°F
 UL 746
RTI Elec (0.0327 in)
°F
 UL 746
Hot-wire Ignition (HWI) (PLC) (0.0327 in)
 
 UL 746
High Amp Arc Ignition (HAI) (PLC) (0.0327 in)
 
 UL 746
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: LONGLITE® PBT 3015-104, LONGLITE PBT 3015104, LONGLITE® PBT , LONGLITE PBT, LONGLITEPBT3015104, LONGLITEPBT, PBT 3015 104, PBT 3015, 3015, PBT3015-104, PBT3015104, PBT3015:104, PBT3015/104, PBT3015+104, PBT3015_104, PBT3015 104, PBT3015, 3015-104, 3015104, 3015:104, 3015/104, 3015+104, 3015_104, 3015 104, Polybutylene Terephthalate, PBT, Polyester, Chang Chun, PolybutyleneTerephthalate, 1043015, 3015PBT
Features
Features may also be described by the following terms: High Heat Resistance, Good Chemical Resistance, Chemical Resistant, Good Weather Resistance, Weather Resistant, Good Wear Resistance, Wear Resistant, Good Moldability.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Holding Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.