IDES Prospector Already have an account? Login Here

IDES

HANWHA LDPE 5312P

Low Density Polyethylene

Supplied by Hanwha Chemical

The technical datasheet with complete property values for HANWHA LDPE 5312P is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HANWHA LDPE 5312P is manufactured by DOW tubular high pressure process and designed for variety of film application such as shrink and greenhouse film. LDPE 5312P has well balanced property of heat shrink, mechanical property and processability.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Features 
  • Additive Free
  • Good Processability
  • High Shrinkage
Uses 
  • Film
  • Shrink Wrap
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Film Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Break)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength
     ASTM D882
MD: Break, 2.0 mil
psi
  
TD: Break, 2.0 mil
psi
  
Tensile Elongation
     ASTM D882
MD: Break, 2.4 mil
%
  
TD: Break, 2.0 mil
%
  
Dart Drop Impact (2.0 mil)
g
 ASTM D1709
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
  
Optical
Nominal Value
Unit
Test Method
Haze (2.36 mil)
%
 ASTM D1003
Additional Information
Nominal Value
Unit
Test Method
Tensile Tear Strength
     ASTM D1004
MD: 2.0 mil
lbf/in
  
TD: 2.0 mil
lbf/in
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HANWHA LDPE 5312P, HANWHA LDPE , HANWHALDPE5312P, HANWHALDPE, LDPE 5312 P, LDPE5312P, LDPE5312, LDPE, 5312 P, 5312P, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, Hanwha, PolyethyleneLowDensity, P5312, 5312LDPE
Features
Features may also be described by the following terms: Good Processability, Easy Processing, High Shrinkage, Additive Free, No Additives.
Uses
Uses may also be described by the following terms: Shrink Wrap.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Blow-up Ratio: 2 to 3
Optimum Gage Range: 0.05 to 0.15 mm
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.