IDES Prospector Already have an account? Login Here

IDES

HANWHA LDPE 955

Low Density Polyethylene

Supplied by Hanwha Chemical

The technical datasheet with complete property values for HANWHA LDPE 955 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HANWHA LDPE 955 is manufactured by autoclave process and designed for variety of extrusion coating application such as flexible packaging, paper coating etc. LDPE 955 is well known for its excellent neck-in, draw-down and high quality assurance.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Features 
  • Additive Free
  • Good Drawdown
  • Good Heat Seal
  • Low Neck-In
  
Uses 
  • Coating Applications
  • Packaging
  • Paper Coatings
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Extrusion Coating
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield
psi
  
Break
psi
  
Tensile Elongation (Break)
%
 ASTM D638
Films
Nominal Value
Unit
Test Method
Water Vapor Transmission
g/100 in²/24 hr
 ASTM F1249
Heat Seal Strength 2
psi
  
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
 ASTM D3417
Additional Information
Nominal Value
Unit
Test Method
Allowable Coating Speed 3
ft/sec
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HANWHA LDPE 955, HANWHA LDPE , HANWHALDPE955, HANWHALDPE, LDPE 955, LDPE955, LDPE, 955, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, Hanwha, PolyethyleneLowDensity, 955LDPE
Features
Features may also be described by the following terms: Low Neck-in, Low Neck In, Good Heat Seal, Good Drawdown, Good draw down, Additive Free, No Additives.
Uses
Uses may also be described by the following terms: Paper Coatings, Paper Coating.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Adapter Temperature
°F
  
Die Temperature
°F
  
Neck-in 3
in
  
Notes
1Typical properties: these are not to be construed as specifications.
2PET (12µm) / Print / LDPE (20µm) / AI Foil (7µm) / LDPE 955 (20µm)
Time/Temperature: 305°C, Line Speed : 100m/min, Output: 80kg/hr
3Melt Temperature : 305?, Line Speed : 100m/min., Output: 80kg/hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.