IDES Prospector Already have an account? Login Here

IDES

HANWHA LLDPE 4100

Linear Low Density Polyethylene

Supplied by Hanwha Chemical

The technical datasheet with complete property values for HANWHA LLDPE 4100 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HANWHA LLDPE 4100 is blended by LDPE with LLDPE and designed for lamination film. LLDPE 4100 has well balanced property of optical property and processability.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Additive 
  • Antiblock
  • Antioxidant
  • Slip
Features 
  • Antiblocking
  • Antioxidant
  • Good Processability
  • Opticals
  • Slip
Uses 
  • Film
  • Laminates
  
Forms 
  • Pellets
Processing Method 
  • Film Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Break)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength
     ASTM D882
MD: Break, 1.2 mil
psi
  
TD: Break, 1.2 mil
psi
  
Tensile Elongation
     ASTM D882
MD: Break, 1.2 mil
%
  
TD: Break, 1.2 mil
%
  
Dart Drop Impact (1.2 mil)
g
 ASTM D1709
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Optical
Nominal Value
Unit
Test Method
Haze (1.18 mil)
%
 ASTM D1003
Additional Information
Tensile Tear Strength, ASTM D1004, 0.03 mm, MD: 100 kg/cm
Tensile Tear Strength, ASTM D1004, 0.03 mm, TD: 100 kg/cm
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HANWHA LLDPE 4100, HANWHA LLDPE , HANWHALLDPE4100, HANWHALLDPE, LLDPE 4100, LLDPE4100, LLDPE, 4100, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Hanwha, PolyethyleneLinearLowDensity, 4100LLDPE
Features
Features may also be described by the following terms: Slip, Unspecified Slip, Good Processability, Easy Processing, Antiblocking, Unspecified Antiblock.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Blow-up Ratio: 2 to 3
Optimum Gage Range: 0.03 to 0.1 mm
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.