IDES Prospector Already have an account? Login Here

IDES

HANWHA CLNB-8141S

Low Density Polyethylene

Supplied by Hanwha Chemical

The technical datasheet with complete property values for HANWHA CLNB-8141S is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HANWHA Wire & Cable Compound CLNB-8141S is a low density, crosslinkable polyethylene compound designed for medium voltage(66kV and higher) power cable insulation requiring a high degree of cleanness. It has a extremely low level of contamination and proper balance of non-staining antioxidant and peroxide to ensure thermal stability and optimum cure levels.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Additive 
  • Antioxidant
Features 
  • Antioxidant
  • Crosslinkable
  • Good Surface Finish
  • Good Thermal Stability
  • High Purity
Uses 
  • Medium Voltage Insulation
  • Wire & Cable Applications
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Degree of Crosslinking
%
 ASTM D2765A
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, 1 sec)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength in Air (277°F, 168 hr)
%
 ASTM D573
Change in Ultimate Elongation in Air (277°F, 168 hr)
%
 ASTM D573
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Additional Information
Nominal Value
Unit
Test Method
Hot Elongation 2 (392°F)
%
 IEC 60811-2-1
Set 2 (392°F)
 
 IEC 60811-2-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HANWHA CLNB-8141S, HANWHA CLNB8141S, HANWHA , HANWHACLNB8141S, CLNB, CLNB 8141 S, CLNB-8141S, CLNB8141S, CLNB:8141S, CLNB/8141S, CLNB+8141S, CLNB_8141S, CLNB 8141S, CLNB8141, 8141S, Polyethylene, Low Density, Polyethylene Low Density, LDPE, Polyethylene, PE, PolyethyleneLowDensity, 8141CLNB
Features
Features may also be described by the following terms: Good Thermal Stability, High Purity, Good Surface Finish.
Uses
Uses may also be described by the following terms: Wire and Cable Applications, Wire & Cable Applications, Medium Voltage Insulation.
Agency Ratings
This plastic material has 11 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ICEA (3), AEIC (2), VDE (1), HD (2), BS (1), IEC (2).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Cure Behavior at 180°C (MDR)
  • Ts1: >1 min
  • Tc90: >5 min
  • Mh-MI: >4.5 lb-in
  • Moisture: <200 ppm
Notes
1Typical properties: these are not to be construed as specifications.
220 N/cm²
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.