IDES Prospector Already have an account? Login Here

IDES

Linathene LL120C

Linear Low Density Polyethylene

Supplied by USI Corporation

The technical datasheet with complete property values for Linathene LL120C is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LINATHENE LL120C is an antioxidant modifier linear low density polyethylene resin for slot cast film extrusion. It is produced using USIFE's UNIPOL gas-phase low-pressure. Films extruded from this resin have good toughness, high tensile strength, elongation, outstanding puncture strength and transparency. LINATHENE LL120C is recommended for the manufacture of stretch film, green film, and other transparent casting applications requiring toughness, puncture resistance and low temperature resistance. It is also recommended for co-extrusion blown film applications requiring like agricultural film, etc. In addition, it is also suitable for isolated material made by compression molding. The resin content of LINATHENE LL120C complies with Food Additive Regulation 177,1520 for Olefin Polymers par(c) 3.2. The Additives presented are sanctioned by appropriate Food Additive Regulations. It follows that LINATHENE LL120C may be used legally for all food packaging applications included holding food during cooking.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Antioxidant
  • Food Contact Acceptable
  • Good Toughness
  • High Tensile Strength
  • Low Density
  • Puncture Resistant
Uses 
  • Agricultural Applications
  • Film
  • Food Packaging
Forms 
  • Pellets
Processing Method 
  • Casting
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D882
MD: Yield
psi
  
TD: Yield
psi
  
MD: Break
psi
  
TD: Break
psi
  
Tensile Elongation
     ASTM D882
MD: Break
%
  
TD: Break
%
  
Dart Drop Impact
g
 ASTM D1709
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Optical
Nominal Value
Unit
Test Method
Gardner Gloss (60°)
 
 ASTM D523
Haze
%
 ASTM D1003
Additional Information
Melting Point, ASTM D2117: 122°C
Shrink Ratio, ASTM D995: 2%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Linathene LL120C, Linathene , LinatheneLL120C, LL 120 C, LL120C, LL120, 120C, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, USI Corporation, PolyethyleneLinearLowDensity, 120LL
Features
Features may also be described by the following terms: Low Density, Low Specific Gravity, High Tensile Strength, Good Toughness, Tough, Good Puncture Resistance, Puncture Resistant.
Uses
Uses may also be described by the following terms: Food Packaging.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.