IDES Prospector Already have an account? Login Here

IDES

SAXATEC™ 4811B

Acrylonitrile Styrene Acrylate

Supplied by SAX Polymers

The technical datasheet with complete property values for SAXATEC™ 4811B is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SAXATEC 4811 is a medium viscosity, low stress cracking ASA injection molding grade, characterized by good impact strength, high stiffness and good resistance to heat distortion.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Impact Resistance
  • High ESCR (Stress Crack Resist.)
  • High Stiffness
  • Medium Heat Resistance
  • Medium Viscosity
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (220°C/10.0 kg)
in³/10min
 ISO 1133
Molding Shrinkage
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2
Tensile Strain (Break, 73°F)
%
 ISO 527-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Notched Izod Impact Strength
     ISO 180/1A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Unnotched Izod Impact Strength
     ISO 180
-22°F
ft·lb/in²
  
73°F
 
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 2 (264 psi, Unannealed, 2.36 in Span)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Additional Information
Moisture Content, B130: <0.2%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SAXATEC™ 4811B, SAXATEC 4811B, SAXATEC™ , SAXATEC, SAXATEC4811B, 4811 B, 4811B, Acrylonitrile Styrene Acrylate, ASA, Sax Polymers, AcrylonitrileStyreneAcrylate, B4811
Features
Features may also be described by the following terms: High Stiffness, Good Impact Resistance, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, Medium Viscosity, Medium Heat Resistance.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
280*10*4mm
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.