IDES Prospector Already have an account? Login Here

IDES

Juner PA-A4-2

Polyamide 6

Supplied by Zhejiang Juner Materials Co., Ltd.

The technical datasheet with complete property values for Juner PA-A4-2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Additive 
  • Flame Retardant
Features 
  • Flame Retardant
  • Medium Gloss
  
Uses 
  • Appliances
  • Connectors
  • Electrical/Electronic Applications
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
%
 ISO 294-4
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in²
 ISO 179
Charpy Unnotched Impact Strength
ft·lb/in²
 ISO 179
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Electrical
Nominal Value
Unit
Test Method
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.126 in)
 
 UL 94
Additional Information
Ash Content, BG/9345: 28%
Chromatism, Delta E: 0.6
Granule Size: 3 mm diameter x 3 to 5 mm
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Juner PA-A4-2, Juner PAA42, Juner , JunerPAA42, PA, PA A 4 2, PA-A4-2, PAA42, PA:A4:2, PA/A4/2, PA+A4+2, PA_A4_2, PA A4 2, PAA, A4, 42, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Zhejiang Juner, Polyamide6, Nylon6, APA
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Medium Gloss.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Notes
The drying conditions above are for a horizontal oven dryer.
Injection Speed: 35 to 80%
Vacuum Drying Temperature, -0.08 MPa: 110°C
Vacuum Drying Time, -0.08 MPa: 2hr
Chute Air Drying Temperature: 120°C
Chute Air Drying Time, -0.08 MPa: 5hr
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.