IDES Prospector Already have an account? Login Here

IDES

C-Polymers CPC0X0APP001

Polypropylene

Carbon Nano Filler, 6.0%

Supplied by C-Polymers GmbH

The technical datasheet with complete property values for C-Polymers CPC0X0APP001 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Filler / Reinforcement 
  • Carbon Nano Filler, 6.0% Filler by Weight
Features 
  • Antistatic
  • Electrically Conductive
  • Good Flow
  • Good Surface Finish
  • High Heat Resistance
  • Thermally Conductive
Uses 
  • Automotive Applications
  • Automotive Exterior Parts
  • Electrical/Electronic Applications
  • Fuel Lines
  • Housings
  • Masterbatch
  • Wire & Cable Applications
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Melt Volume-Flow Rate (MVR) (230°C/2.16 kg)
in³/10min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2 (Injection Molded)
psi
 ISO 527-2
Tensile Stress 2 (Yield, Injection Molded)
psi
 ISO 527-2
Tensile Strain 2 (Yield, Injection Molded)
%
 ISO 527-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 2 (Injection Molded)
ft·lb/in²
 ISO 179/1eA
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 2 (66 psi, Unannealed)
°F
 ISO 75-2/B
Melting Temperature
°F
 ISO 11357-3
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 Internal Method
Volume Resistivity
ohm·cm
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: C-Polymers CPC0X0APP001, CPolymers CPC0X0APP001, C-Polymers , CPolymers, C:Polymers, C/Polymers, C+Polymers, C_Polymers, C Polymers, CPolymersCPC0X0APP001, CPC 0 X 0 APP 001, CPC0X0APP001, CPC0, 0X, X0, 0APP, APP001, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, PolypropyleneUnspecified, PPUnspecified, 0CPC
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Electrically Conductive, Conducts Electricity, Conductive, Good Flow, High Heat Resistance, Good Surface Finish.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Housings, Housing, Wire and Cable Applications, Wire & Cable Applications.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Holding Pressure: min required to avoid sink marks
Drying: not required
Notes
1Typical properties: these are not to be construed as specifications.
2Values determined on injection molded specimens according to ISO 3167, based on ISO 291 conditions.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.