IDES Prospector Already have an account? Login Here

IDES

RESOLE FM 4029F

Phenolic

Glass Fiber Reinforcement

Supplied by Vyncolit N.V.

The technical datasheet with complete property values for RESOLE FM 4029F is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement
Features 
  • Acid Resistant
  • Base Resistant
  • Fungus Resistant
  • Good Creep Resistance
  • Good Dimensional Stability
  • High Strength
  • Low Smoke Emission
  • Solvent Resistant
  • Ultra High Toughness
Uses 
  • Appliances
  • Automotive Applications
  • Connectors
  • Electrical/Electronic Applications
  • Gears
  • Housings
  • Membrane Touch Switches
  • Power/Other Tools
  • Pump Parts
Agency Ratings 
Forms 
  • Granules
Processing Method 
  • Compression Molding
  • Injection Molding
  • Resin Transfer Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Bulk Factor
 
 ASTM D1895
Molding Shrinkage - Flow (Compression Molded)
in/in
 ASTM D955
Water Absorption (73°F, 24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (E-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
CLTE - Flow
in/in/°F
 ASTM D696
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RESOLE FM 4029F, RESOLE , RESOLEFM4029F, FM 4029 F, FM 4029F, FM4029, 4029F, FM4029F, Phenolic, Vyncolit, 4029FM
Features
Features may also be described by the following terms: Ultra High Toughness, High Strength, Low Smoke Emission, Good Dimensional Stability, Dimensionally Stable, Good Creep Resistance, Creep Resistant.
Uses
Uses may also be described by the following terms: Power Tools, Tools, Membrane Touch Switches, Housings, Housing, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Automotive Applications, Automotive Sector.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ASTM (1).
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Injection Notes
Plastication: 50rpm
Injection Pressure: Set to give 3 to 5 seconds injection time
Hold Pressure: 50 to 100% of injection pressure
Hold Time: 10 sec minimum
Cure Time, 0.125 in: 30 to 35 sec
Water Absorption, ASTM D570, 48 hrs, 50°C: 0.15%
DTUL @264psi - Unannealed, ASTM D648, Post Baked: 550°F
Bulk Factor, ASTM D1895: 1.8 to 2.3
Compression and Transfer Molding Conditions:
  • Preforming Pressure: 8000 to 12000 psi
  • Preheat Temperature: 210 to 235 °F
  • Preheat Time: 45 sec
  • Mold Temperature: 330 to 360 °F
  • Compression Mold Pressure: 2500 to 5000 psi
  • Transfer Mold Pressure: 4000 to 6000 psi
  • Cure Time, 0.125 in: 40 to 50 sec
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.