IDES Prospector Already have an account? Login Here

IDES

NOVALAC FM 7700

Phenolic

Cellulose Filler

Supplied by Vyncolit N.V.

The technical datasheet with complete property values for NOVALAC FM 7700 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Cellulose Filler
Features 
  • Acid Resistant
  • Base Resistant
  • Good Creep Resistance
  • Good Dimensional Stability
  • Low Smoke Emission
  • Solvent Resistant
Uses 
  • Appliances
  • Automotive Applications
  • Connectors
  • Electrical/Electronic Applications
  • Gears
  • Housings
  • Membrane Touch Switches
  • Power/Other Tools
  • Pump Parts
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Compression Molding
  • Injection Molding
  • Resin Transfer Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Bulk Factor
 
 ASTM D1895
Molding Shrinkage - Flow (Compression Molded)
in/in
 ASTM D955
Water Absorption (73°F, 24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength
     ASTM D149
-- 2
V/mil
  
-- 3
V/mil
  
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0625 in)
 
 UL 94
UL
Nominal Value
Unit
Test Method
RTI Str
°F
 UL 746
RTI Imp
°F
 UL 746
RTI Elec
°F
 UL 746
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: NOVALAC FM 7700, NOVALAC , NOVALACFM7700, FM 7700, FM7700, Phenolic, Vyncolit, 7700FM
Features
Features may also be described by the following terms: Low Smoke Emission, Good Dimensional Stability, Dimensionally Stable, Good Creep Resistance, Creep Resistant.
Uses
Uses may also be described by the following terms: Power Tools, Tools, Membrane Touch Switches, Housings, Housing, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Automotive Applications, Automotive Sector.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ASTM (1).
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Injection Notes
Plastication: 50 to 65rpm
Injection Pressure: Set to give 6 to 10 seconds injection time
Hold Pressure: 50 to 100% of injection pressure
Hold Time: 15 sec minimum
Cure Time, 0.125 in: 40 to 45 sec
Water Absorption, ASTM D570, 48 hrs, 50°C: 2.2%
Dielectric Strength, ASTM D149, 60 Hz, Method A, wet: 140 V/mil
Dielectric Strength, ASTM D149, 60 Hz, Method B, wet: 80 V/mil
Bulk Factor, ASTM D1895: 3.6 to 4.6
Compression and Transfer Molding Conditions:
  • Preforming Pressure: 8000 to 12000 psi
  • Preheat Temperature: 210 to 235 °F
  • Preheat Time: 45 sec
  • Mold Temperature: 330 to 360 °F
  • Compression Mold Pressure: 2500 to 5000 psi
  • Transfer Mold Pressure: 4000 to 6000 psi
  • Cure Time, 0.125 in: 40 to 50 sec
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
3Method B (Step-by-Step)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.