IDES Prospector Already have an account? Login Here

IDES

SABIC® PPcompound 2605-1

Polypropylene

Talc Filler

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® PPcompound 2605-1 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® PPcompound 2605/1 is a talc-filled elastomer-modified material. The good balance between impact and stiffness and it's low-density make it suited for injection-molded dashboards and interior trim. This material was optimized for low smell, low emission and good paintablility. SABIC® PPcompound 2605/1 is a designated automotive grade.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Talc Filler
Features 
  • Good Impact Resistance
  • Good Stiffness
  • Low Density
  • Low to No Odor
  • Paintable
Uses 
  • Automotive Interior Parts
  • Automotive Interior Trim
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
     ISO 527-2/5/50
Yield, 0.126 in, Injection Molded
psi
  
Break, 0.126 in, Injection Molded
psi
  
Tensile Strain (Break, 0.126 in, Injection Molded)
%
 ISO 527-2/5/50
Flexural Modulus 2 (Injection Molded)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F, Injection Molded)
 
 ISO 179/1eA
Charpy Unnotched Impact Strength (-40°F)
 
 ISO 179/1eU
Notched Izod Impact Strength
     ISO 180/4A
-4°F
ft·lb/in²
  
32°F
ft·lb/in²
  
73°F
 
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (66 psi, Unannealed)
°F
 ISO 75-2/B
Vicat Softening Temperature
°F
 ISO 306/A
CLTE - Flow
     ASTM D696
-22 to 86°F
in/in/°F
  
73 to 176°F
in/in/°F
  
Additional Information
Mould shrinkage, SABIC method, 24 hours after injection moulding: 1.2%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® PPcompound 2605-1, SABIC PPcompound 26051, SABIC® PPcompound , SABIC PPcompound, SABICPPcompound26051, SABICPPcompound, PPcompound 2605 1, PPcompound 2605, 2605, PPcompound2605-1, PPcompound26051, PPcompound2605:1, PPcompound2605/1, PPcompound2605+1, PPcompound2605_1, PPcompound2605 1, PPcompound2605, 2605-1, 26051, 2605:1, 2605/1, 2605+1, 2605_1, 2605 1, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, SABIC, PolypropyleneUnspecified, PPUnspecified, 12605, 2605PPcompound
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Good Impact Resistance, Good Stiffness, Low Density, Low Specific Gravity, Low Odor.
Notes
1Typical properties: these are not to be construed as specifications.
2Method I (3 point load)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.