IDES Prospector Already have an account? Login Here

IDES

QR Resin QR-4004

Polyphenylene Ether + Nylon 66

Supplied by QTR, Inc.

The technical datasheet with complete property values for QR Resin QR-4004 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Chemical Resistance
  • Paintable
  
Appearance 
  • Black
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (280°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: QR Resin QR-4004, QR Resin QR4004, QR Resin , QRResinQR4004, QRResin, QR, ResinQR-4004, ResinQR4004, ResinQR:4004, ResinQR/4004, ResinQR+4004, ResinQR_4004, ResinQR 4004, ResinQR, QR-4004, QR4004, QR:4004, QR/4004, QR+4004, QR_4004, QR 4004, Polyphenylene Ether + Nylon 66, Polyphenylene Ether Nylon 66, Polyphenylene Ether : Nylon 66, Polyphenylene Ether / Nylon 66, Polyphenylene Ether - Nylon 66, Polyphenylene Ether _ Nylon 66, Polyphenylene Ether Nylon 66, PPE+Nylon 66, PPENylon 66, PPE:Nylon 66, PPE/Nylon 66, PPE-Nylon 66, PPE_Nylon 66, PPE Nylon 66, Polyphenylene Ether, PPE, QTR, PolyphenyleneEtherNylon66, PPENylon66, PolyphenyleneEther, PolyphenyleneEther_Nylon66, PPE_Nylon66, 4004QR, 4004ResinQR
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.