Celanex 1400A Ticona Polybutylene Terephthalate

Product Description

Celanex 1400A is a general purpose, unreinforced polybutylene terephthalate with a good balance of mechanical properties and processability. Celanex 1400A is a high flow material.

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Asia Pacific

Europe

Latin America

North America

South America

Features

General Purpose

Good Processability

High Flow

Uses

General Purpose

RoHS Compliance

Processing Method

Injection Molding

Multi-Point Data

Isothermal Stress vs. Strain (ISO 11403-1)

Physical	Nominal Value	Unit	Test Method
Specific Gravity
--			ASTM D792
--		g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR)		g/10 min	ASTM D1238
Molding Shrinkage - Flow
--		in/in	ASTM D955
--		%	ISO 294-4
Water Absorption (73°F, 24 hr)		%	ASTM D570
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1A/1
Tensile Strength
Yield, 73°F		psi	ASTM D638
Yield		psi	ISO 527-2/1A/50
Break, 73°F		psi	ASTM D638
Tensile Strain
Yield		%	ISO 527-2/1A/50
Break, 73°F		%	ASTM D638
Nominal Tensile Strain at Break		%	ISO 527-2/1A/50
Flexural Modulus
73°F		psi	ASTM D790
73°F		psi	ISO 178
Flexural Strength
73°F		psi	ASTM D790
73°F		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Notched Izod Impact
73°F		ft·lb/in	ASTM D256
73°F		ft·lb/in²	ISO 180/1A
Hardness	Nominal Value	Unit	Test Method
Rockwell Hardness (M-Scale)			ISO 2039-2
Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load
66 psi, Unannealed		°F	ASTM D648
66 psi, Unannealed		°F	ISO 75-2/B
264 psi, Unannealed		°F	ASTM D648
264 psi, Unannealed		°F	ISO 75-2/A
Glass Transition Temperature		°F	ISO 11357-2
Melting Temperature²		°F	ISO 11357-3, ASTM D3418
CLTE - Flow		in/in/°F	ISO 11359-2
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohms	IEC 60093
Volume Resistivity		ohm·cm	ASTM D257, IEC 60093
Dielectric Strength
--³		V/mil	ASTM D149
--		V/mil	IEC 60243-1
Relative Permittivity (1 MHz)			IEC 60250
Dissipation Factor
1 kHz			ASTM D150
1 MHz			IEC 60250
Arc Resistance		sec	ASTM D495
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
--
0.0295 in
Related Terminology
This supplier and product may also be known by these terms: Celenex Product names can be difficult to match. You may have searched any one of these terms to find this product: Celanex® 1400A, Celanex 1400A, Celanex® , Celanex, Celanex1400A, 1400 A, 1400A, Polybutylene Terephthalate, PBT, Polyester, Ticona, PolybutyleneTerephthalate, A1400
Features
Features may also be described by the following terms: Good Processability, Easy Processing, High Flow, High Melt, High MFI.

Injection	Nominal Value	Unit
Suggested Max Regrind		%
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Rate
Back Pressure		psi
Injection Notes
Screw Speed: Medium Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades. Up to 25% clean and dry regrind may be used.

Notes

¹Typical properties: these are not to be construed as specifications.

²10°C/min

³Method A (Short-Time)

Celanex® 1400A

Polybutylene Terephthalate

Supplied by Ticona