IDES Prospector Already have an account? Login Here

IDES

WaterShed™ 11110

Thermoset, Unspecified

Supplied by DSM Somos®

The technical datasheet with complete property values for WaterShed™ 11110 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
DSM Somos® 11110 is a low viscosity liquid photopolymer that produces strong, tough, water-resistant parts. Parts created with Somos® 11110 have a light green tinge, similar in color to plate glass.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Toughness
  • Low Viscosity
  
Uses 
  • Automotive Applications
  • Consumer Applications
  • Electrical/Electronic Applications
  • Medical/Healthcare Applications
  • Prototyping
Appearance 
  • Clear/Transparent
Forms 
  • Liquid
Processing Method 
  • Stereo Lithography
Physical
Nominal Value
Unit
Test Method
Water Absorption (Saturation)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation
     ASTM D638
Yield
%
  
Break
%
  
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Glass Transition Temperature
°F
 ASTM E1356
CLTE - Flow
     ASTM D696
-40 to 32°F
in/in/°F
  
32 to 122°F
in/in/°F
  
122 to 212°F
in/in/°F
  
212 to 302°F
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
60 Hz
 
  
1 kHz
 
  
1 MHz
 
  
Optical
Nominal Value
Unit
Test Method
Refractive Index
 
 ASTM D542
Additional Information
The value listed as Glass Transition Temperature, ASTM E1356, was tested in accordance with ASTM E1545.
Viscosity, 30°C: 92 cps
Density (liquid), 25°C: 1.12 g/cm³
Optical Properties at 325 nm:
  • Dp (slope of cure-depth vs. ln(E) curve): 0.14 mm
  • Ec (critical exposure): 11.5 mJ/cm²
  • E10 (exposure that gives 0.254 mm (0.010 in) thickness): 72 mJ/cm²
Tear Strength (Graves), ASTM D1004: 132746 N/m
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: WaterShed™ 11110, WaterShed 11110, WaterShed™ , WaterShed, WaterShed11110, 11110, Thermoset, Unspecified, Thermoset Unspecified, TS, Unspecified, TS Unspecified, Thermoset, TS, ThermosetUnspecified, TSUnspecified
Features
Features may also be described by the following terms: Low Viscosity, Good Toughness, Tough.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector, Medical Applications, Automotive Applications, Automotive Sector.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.