IDES Prospector Already have an account? Login Here

IDES

UBE Nylon P7115 U

Polyamide 612

Supplied by UBE Engineering Plastics, S.A.

The technical datasheet with complete property values for UBE Nylon P7115 U is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
UBESTA P7115 U is a low viscosity, non-reinforced and non-plasticized Polyamide 12/6 copolymer powder.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Heat Stabilizer
Features 
  • Good Flow
  • Good Moldability
  • Heat Stabilized
  • Low Viscosity
  
Appearance 
  • Natural Color
Forms 
  • Powder
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/1.0 kg)
g/10 min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain
     ISO 527-2
Yield
%
  
Break
%
  
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-40°F, Complete Break
ft·lb/in²
  
73°F, Complete Break
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ISO 2039-2
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Melting Temperature (DSC)
°F
 ISO 3146
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Additional Information
The value listed as Melting Temperature, ISO 3146, was tested in accordance with ISO 11357.
Tensile Strain at Break, ISO 527: >300%
Abrasion Loss, ISO 9352, CS-17, 1000 rev.: 5 mg
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: UBE Nylon P7115 U, UBE Nylon , UBENylonP7115U, UBENylon, NylonP 7115 U, NylonP7115 U, NylonP7115, Nylon, P 7115 U, NylonP7115U, P7115 U, P7115, 7115U, P7115U, Polyamide 612, Nylon 612, Polyamide, pa612, UBE Engineering Plastics, Polyamide612, Nylon612, 7115P, 7115NylonP
Generic Name
Generic Name may also be described by the following terms: PA612, PA6/12.
Features
Features may also be described by the following terms: Good Moldability, Low Viscosity, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good Flow.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.