IDES Prospector Already have an account? Login Here

IDES

UBESTA 3030 JI6L

Polyamide 12

Supplied by UBE Engineering Plastics, S.A.

The technical datasheet with complete property values for UBESTA 3030 JI6L is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
UBESTA 3030 JI6L is a plasticized and impact modified PA12 grade. The material is stabilized against weatherability. The grade is mostly applied for multilayer tubes. It shows excellent bonding to ETFE and other fluoroplastics.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Impact Modifier
  • Plasticizer
  
Features 
  • Good Adhesion
  • Good Impact Resistance
  • Good Processability
  • Impact Modified
  • Plasticized
Uses 
  • Tubing
Appearance 
  • Black
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (235°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain
     ISO 527-2
Yield
%
  
Break
%
  
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-40°F, Complete Break
ft·lb/in²
  
73°F, Partial Break
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ISO 2039-2
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Melting Temperature (DSC)
°F
 ISO 3146
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Additional Information
The value listed as Melting Temperature, ISO 3146, was tested in accordance with ISO 11357.
Tensile Strain at Break, ISO 527: >200%
Abrasion Loss, ISO 9352, CS-17, 1000 rev.: 7 mg
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: UBESTA 3030 JI6L, UBESTA , UBESTA3030JI6L, 3030 JI 6 L, 3030 JI6L, 3030JI, JI6, 6L, 3030JI6L, Polyamide 12, Nylon 12, Polyamide, Nylon, pa12, UBE Engineering Plastics, Polyamide12, Nylon12, JI3030
Generic Name
Generic Name may also be described by the following terms: PA12.
Features
Features may also be described by the following terms: Good Impact Resistance, Good Adhesion, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Tubing, Tube.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.