IDES Prospector Already have an account? Login Here

IDES

Uniprene® UN-1141A

Thermoplastic Vulcanizate

Supplied by Teknor Apex Company

The technical datasheet with complete property values for Uniprene® UN-1141A is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Uses 
  • Expansion Joint
  • Gaskets
  • Glazing
  • Grommets
  • Plugs
  • Shock Absorbing Pads
  • Tubing
  • Weatherstripping
Appearance 
  • Opaque
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ASTM D1238
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (100% Strain)
psi
 ASTM D412
Tensile Strength (Yield)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Tear Strength
lbf/in
 ASTM D624
Compression Set
     ASTM D395B
73°F, 22.0 hr
%
  
212°F, 22.0 hr
%
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Uniprene® UN-1141A, Uniprene UN1141A, Uniprene® , Uniprene, UnipreneUN1141A, UN, UN 1141 A, UN-1141A, UN1141A, UN:1141A, UN/1141A, UN+1141A, UN_1141A, UN 1141A, UN1141, 1141A, Thermoplastic Vulcanizate, TPV, Thermoplastic Elastomer, TPE, Teknor Apex, ThermoplasticVulcanizate, ThermoplasticElastomer, 1141UN
Uses
Uses may also be described by the following terms: Gaskets, Gasketing, Shock Absorbing Pads, Tubing, Tube.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
Screw Speed: 30 to 100 rpm
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.