IDES Prospector Already have an account? Login Here

IDES

THERMOLAST® K TF1STL (Series: FD/S)

Thermoplastic Elastomer

Supplied by KRAIBURG TPE Corporation

The technical datasheet with complete property values for THERMOLAST® K TF1STL (Series: FD/S) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Appearance 
  • Translucent
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (Break)
psi
ISO 37
Tensile Elongation (Break)
%
ISO 37
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore A)
 
ISO 868
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: THERMOLAST® K TF1STL, THERMOLAST K TF1STL, THERMOLAST® K TF1STL (Series: FD/S), THERMOLAST K TF1STL Series FDS, THERMOLAST® K , THERMOLAST K, THERMOLASTKTF1STLSeriesFDS, THERMOLASTK, TF 1 STL, TF 1 STL Series, KTF1STL, KTF 1 STL Series FD S, KTF 1 STL, KTF 1 STL Series, TF1STL (Series, TF1STL Series, KTF1STL (Series: FD/S), KTF1STL Series FDS, KTF1STL (Series/ FD/S), KTF1STL (Series+ FD/S), KTF1STL (Series- FD/S), KTF1STL (Series_ FD/S), KTF1STL (Series FD/S), KTF1STL (Series: FD:S), KTF1STL (Series: FD+S), KTF1STL (Series: FD-S), KTF1STL (Series: FD_S), KTF1STL (Series: FD S), KTF1, KTF1STL (Series, KTF1STL Series, TF1STL, TF 1 STL Series FD S, TF1STLSeries, KTF1STLSeriesFDS, KTF1STL Series_ FDS, KTF1STL Series FD_S, KTF1STL Series FD S, KTF1STLSeries, TF1STL (Series: FD/S), TF1STL Series FDS, TF1STL (Series/ FD/S), TF1STL (Series+ FD/S), TF1STL (Series- FD/S), TF1STL (Series_ FD/S), TF1STL (Series FD/S), TF1STL (Series: FD:S), TF1STL (Series: FD+S), TF1STL (Series: FD-S), TF1STL (Series: FD_S), TF1STL (Series: FD S), TF1, 1STL, STLSeries, SeriesFD, FDS, KTF1STLSeries_FDS, KTF1STLSeriesFD_S, TF1STLSeriesFDS, TF1STL Series_ FDS, TF1STL Series FD_S, TF1STL Series FD S, TF1STLSeries_FDS, TF1STLSeriesFD_S, Thermoplastic Elastomer, TPE, Kraiburg TPE, ThermoplasticElastomer, 1TF, 1KTF
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Mold Temperature
°F
 
Injection Pressure
psi
 
Injection Rate
 
 
Back Pressure
psi
 
Injection Notes
Hot Runner Temperature: 200 to 250°C
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.