IDES Prospector Already have an account? Login Here

IDES

THERMOLAST® K TC4GPZ (Series: GP/HM)

Styrene Ethylene Butylene Styrene Block Copolymer

Supplied by KRAIBURG TPE Corporation

The technical datasheet with complete property values for THERMOLAST® K TC4GPZ (Series: GP/HM) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Features 
  • Good Weather Resistance
Uses 
  • Outdoor Applications
Appearance 
  • Black
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress     ISO 37
100% Strain
psi
  
200% Strain
psi
  
300% Strain
psi
  
Tensile Stress (Break)
psi
 ISO 37
Tensile Elongation (Break)
%
 ISO 37
Tear Strength 2
lbf/in
 ISO 34-1
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore A)
 
 ISO 868
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Additional Information
Nominal Value
Unit
Test Method
ISO Type
 
 ISO 18064
Weather Resistance 3
ft·lb/in²
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: THERMOLAST® K TC4GPZ, THERMOLAST K TC4GPZ, THERMOLAST® K TC4GPZ (Series: GP/HM), THERMOLAST K TC4GPZ Series GPHM, THERMOLAST® K , THERMOLAST K, THERMOLASTKTC4GPZSeriesGPHM, THERMOLASTK, TC 4 GPZ, TC 4 GPZ Series, KTC4GPZ, KTC 4 GPZ Series GP HM, KTC 4 GPZ, KTC 4 GPZ Series, TC4GPZ (Series, TC4GPZ Series, KTC4GPZ (Series: GP/HM), KTC4GPZ Series GPHM, KTC4GPZ (Series/ GP/HM), KTC4GPZ (Series+ GP/HM), KTC4GPZ (Series- GP/HM), KTC4GPZ (Series_ GP/HM), KTC4GPZ (Series GP/HM), KTC4GPZ (Series: GP:HM), KTC4GPZ (Series: GP+HM), KTC4GPZ (Series: GP-HM), KTC4GPZ (Series: GP_HM), KTC4GPZ (Series: GP HM), KTC4, KTC4GPZ (Series, KTC4GPZ Series, TC4GPZ, TC 4 GPZ Series GP HM, TC4GPZSeries, KTC4GPZSeriesGPHM, KTC4GPZ Series_ GPHM, KTC4GPZ Series GP_HM, KTC4GPZ Series GP HM, KTC4GPZSeries, TC4GPZ (Series: GP/HM), TC4GPZ Series GPHM, TC4GPZ (Series/ GP/HM), TC4GPZ (Series+ GP/HM), TC4GPZ (Series- GP/HM), TC4GPZ (Series_ GP/HM), TC4GPZ (Series GP/HM), TC4GPZ (Series: GP:HM), TC4GPZ (Series: GP+HM), TC4GPZ (Series: GP-HM), TC4GPZ (Series: GP_HM), TC4GPZ (Series: GP HM), TC4, 4GPZ, GPZSeries, SeriesGP, GPHM, KTC4GPZSeries_GPHM, KTC4GPZSeriesGP_HM, TC4GPZSeriesGPHM, TC4GPZ Series_ GPHM, TC4GPZ Series GP_HM, TC4GPZ Series GP HM, TC4GPZSeries_GPHM, TC4GPZSeriesGP_HM, Styrene Ethylene Butylene Styrene Block Copolymer, SEBS, Thermoplastic Elastomer, TPE, Kraiburg TPE, StyreneEthyleneButyleneStyreneBlockCopolymer, ThermoplasticElastomer, 4TC, 4KTC
Features
Features may also be described by the following terms: Good Weather Resistance, Weather Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Injection Notes
Hot Runner Temperature: 200 to 250°C
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Adapter Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
Compression Ratio: At least 3.5:1
Mold Clamping Zone: 3 to 5 mm
Screw Length: 25D
Notes
1Typical properties: these are not to be construed as specifications.
2Method Bb, Angle (Nicked)
3dE=1.030
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.