IDES Prospector Already have an account? Login Here

IDES

Iupiace® EHM1010A

Polyphenylene Ether + PS

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for Iupiace® EHM1010A is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Additive 
  • Antistatic
Features 
  • Antistatic
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
      
Across Flow: 0.126 in
%
  
Flow: 0.126 in
%
  
Water Absorption (Saturation, 73°F)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Break, 73°F)
psi
 ISO 527-2
Tensile Strain (Break, 73°F)
%
 ISO 527-2
Flexural Modulus (73°F)
psi
 ISO 178
Flexural Strength (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
CLTE
     ISO 11359-2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Related Terminology
This supplier and product may also be known by these terms: Lupiace, Jupiace

Product names can be difficult to match. You may have searched any one of these terms to find this product: Iupiace® EHM1010A, Iupiace EHM1010A, Iupiace® , Iupiace, IupiaceEHM1010A, EHM 1010 A, EHM1010A, EHM1010, 1010A, Polyphenylene Ether + PS, Polyphenylene Ether PS, Polyphenylene Ether : PS, Polyphenylene Ether / PS, Polyphenylene Ether - PS, Polyphenylene Ether _ PS, Polyphenylene Ether PS, PPE+PS, PPEPS, PPE:PS, PPE/PS, PPE-PS, PPE_PS, PPE PS, Polyphenylene Ether, PPE, Mitsubishi EP, PolyphenyleneEtherPS, PolyphenyleneEther, PolyphenyleneEther_PS, 1010EHM
Generic Name
Generic Name may also be described by the following terms: PPO.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.