IDES Prospector Already have an account? Login Here

IDES

PENTAMID AHT MC30 H ungefärbt

Polyamide 46

Mineral Filler, 30%

Supplied by PENTAC Polymer GmbH

The technical datasheet with complete property values for PENTAMID AHT MC30 H ungefärbt is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Normal viscosity, heat stabilised polyamide 4.6, easy flow, 30% special mineral reinforced
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Mineral Filler, 30% Filler by Weight
Additive 
  • Heat Stabilizer
Features 
  • Good Flow
  • Heat Stabilized
  
Uses 
  • Automotive Under the Hood
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption
     ISO 62
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Viscosity Number
cm³/g
 ISO 307
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eU
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 961/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Melting Temperature (DSC)
°F
 ISO 3146
Electrical
Nominal Value
Unit
Test Method
Relative Permittivity (1 MHz)
 
 IEC 60250
Comparative Tracking Index
V
 IEC 60112
Electric Strength (0.0394 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.126 in)
 
 UL 94
Additional Information
ISO Description: PA4.6, MHR, 18-120 N, MD30
The value listed as Melting Point, ISO 3146, was tested in accordance with ISO 11357.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: PENTAMID AHT MC30 H ungefärbt, PENTAMID AHT , PENTAMIDAHTMC30Hungefärbt, PENTAMIDAHT, AHTMC 30 H ungef rbt, AHTMC30 H ungefärbt, AHTMC30, AHT, MC 30 H ungef rbt, AHTMC30Hungefärbt, MC30 H ungefärbt, MC30, 30H, Hungef, ungefrbt, MC30Hungefärbt, Polyamide 46, Nylon 46, Polyamide, Nylon, pa46, Polyamide46, Nylon46, 30MC, 30AHTMC
Generic Name
Generic Name may also be described by the following terms: PA46.
Features
Features may also be described by the following terms: Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good Flow.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Screw L/D Ratio
 
  
Screw Compression Ratio
 
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.