IDES Prospector Already have an account? Login Here

IDES

AD majoris DT 231

Polypropylene

Mineral Filler, 20%

Supplied by AD majoris

The technical datasheet with complete property values for AD majoris DT 231 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
DT 231 is a 20% mineral filled polypropylene compound intended for injection moulding.

DT 231 is a medium flow rate grade with good process ability.

APPLICATIONS
Under bonnet applications requiring good long-term heat stability, low shrinkage, high dimensional stability and high heat distortion temperature…
  • Connectors boxes
  • Air filters
  • Air ducts
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Mineral Filler, 20% Filler by Weight
Additive 
  • Heat Stabilizer
Features 
  • Good Processability
  • Good Thermal Stability
  • Heat Stabilized
  • Low Shrinkage
  • Medium Flow
Uses 
  • Automotive Under the Hood
  • Connectors
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage - Flow (73°F)
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield, 73°F, Injection Molded)
psi
 ISO 527-2/50
Tensile Strain (Yield, 73°F, Injection Molded)
%
 ISO 527-2/50
Flexural Modulus 2 (73°F, Injection Molded)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-4°F, Injection Molded
ft·lb/in²
  
73°F, Injection Molded
ft·lb/in²
  
Charpy Unnotched Impact Strength (73°F, Injection Molded)
ft·lb/in²
 ISO 179/1eU
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 358/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Additional Information
Fogging, DIN 75201, 100°C/16h: 0.3 mg
Emission:, VDA 277: 21 µg C/g
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: AD majoris DT 231, AD majoris , ADmajorisDT231, ADmajoris, majorisDT 231, majoris, majorisDT231, DT 231, DT231, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, PolypropyleneUnspecified, PPUnspecified, 231DT, 231majorisDT
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Medium Flow, Medium Melt, Medium MFI, Good Processability, Easy Processing, Low Shrinkage, Good Thermal Stability.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Hold-on Pressure: 50 - 70% of the injection pressure
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.